We found 123939 price guide item(s) matching your search

A THIRTY-HOUR LONGCASE CLOCK MOVEMENT AND A NINE-AND-THREE-QUARTER-INCH DIALTHE DIAL INSCRIBED FOR JOHN SNOW, FROME, EARLY 18th CENTURYThe four-finned pillar countwheel striking movement with break-arch shaped plates and anchor escapement for regulation by a seconds pendulum, now fitted with a square brass dial with calendar aperture to the matted centre within applied Roman numeral chapter ring with lozenge half hour markers and engraved John. Snow, Froo... to lower margin, with steel hand and winged mask and scroll cast spandrels to angles with herringbone engraved infill between, (no pendulum, weight or bell); together with a six inch wall clock dial engraved CROOME, WOTTON to the lower edge of the Roman numeral chapter ring, and a small collection of posted longcase and lantern clock parts, including a rare 'first period' lantern clock fret, (qty).The movement and dial 29cm (11.5ins) high, 14cm (5.5ins) deep, 25cm (9,75ins) wide. The lantern clock fret included in the current lot is of the type used on the celebrated early 'first period' clock by Thomas Harvey which is fully described and illustrated in Hooper, John and Darken, Jeff English 30 Hour Clocks, Their Origin and Development 1600-1800 pages 16-22. 

A GEORGE III BRASS MOUNTED MAHOGANY BRACKET CLOCK WITH TRIP-HOUR REPEATTHE DIAL BEARING INSCRIPTION FOR THWAITES AND REED, LONDON, CIRCA 1800The five pillar twin fusee bell striking movement with verge escapement regulated by short bob pendulum incorporating holdfast clasp to the basket-of-fruit centred symmetrical foliate scroll engraved backplate, the 8 inch circular cream painted Roman numeral dial now inscribed Thwaites & Reed, LONDON to centre and with gilt spade, the upper margin of the dial surround with N/S strike/silent selection switch, the break-arch case with hinged brass carrying handle to the brass-fillet moulded single pad top panel over complex moulded cornice, the hinged front panel fitted with convex glazed ogee cast brass bezel over brass fish scale lower quadrant frets flanked by brass edged front angles, the sides with conforming arched brass frets and the rear with break-arch door set within the frame of the case, on cavetto moulded skirt base with brass ogee bracket feet.40.5cm (16ins) high with handle down, 31cm (12.25ins) wide, 19.5cm (7.75ins) deep.Condition Report: Movement is in relatively clean working condition and has no visible evidence of alteration or noticeable replacements. The dial has been restored to a good standard as such the inscription for Thwaites and Reed cannot be relied upon. Other than some very light wear around the winding holes and some light surface dirt the dial is in fine condition. The case is generally in fine original condition with good quality figured veneers. The top is free of noticeable shrinkage cracking. The rear door has a small veneer patch repair to the upper left-hand corner otherwise faults to the case appear very much limited to a few minor bumps and scuffs, light shrinkage and other minimal age related blemishes. Clock has a crank winder and two case keys. Condition Report Disclaimer

A WALNUT EIGHT-DAY LONGCASE CLOCKTHE DIAL SIGNED JAMES GAMBLE, LEEDS, LATE 17th CENTURY AND LATERThe five finned pillar inside countwheel bell striking movement with anchor escapement regulated by seconds pendulum, the 11 inch square brass dial with ringed winding holes, elaborate sculpted border decorated calendar aperture and subsidiary seconds dial to the rose engraved matted centre, within applied silvered Roman numeral chapter ring with sword hilt half hour markers and Arabic five minutes beyond the minute track, with fine generous sculpted steel hands and cherub mask and scroll cast spandrels to angles with foliate scroll engraved infill between and signed James Gamble at Leeds to lower edge, now in a case with complex moulded cornice over hinged glazed dial aperture applied with Doric columns to angles, rectangular side windows and conforming quarter columns set against bargeboards at the rear, the trunk with concave throat moulding over rectangular caddy moulded quarter veneered and crossbanded door flanked by reeded canted angles, the plinth base with stepped cavetto top mouldings and conforming herringbone banded panel to fascia over double skirt.214cm (84.25ins) high, 46cm (18ins) wide, 27.5cm (10.75ins) deep. James Gamble of Leeds does not appear to be recorded I the usual sources however the overall feel of the movement and the style/design of the engraving to the design would suggest that he was a London-trained clock maker.Condition Report: The movement is in very dirty/neglected condition. The escapement is a 19th century replacement (most likely due to the wear of the original) and the warning wheel of the strike train has been re-pinioned (again most likely due to wear). Otherwise the movement has survived in original condition and will no doubt work well once it has had a straightforward clean/service. The dial again is in dirty/neglected condition with general oxidation and grime build-up to the finishes. However it does appear very original and essentially untouched with very nice hands and confidently worked details such as the decoration to the calendar aperture. The movement retains an old (possibly original) seatboard. The case is not original to the movement and dial. The cheeks are later being separately applied to the inside edges of the trunk sides and one (the left hand side) is currently detached hence movement and dial cannot currently be supported within the case. The hood is entirely of early to mid 20th century construction and is generally in good condition albeit a lttle dirty/neglected. The rest of the case would appear to date to around 1730 and is of nice quality with fine figured veneers and is in good honest original condition. The sides of the trunk have some veneer chipping to the rear edges and there is overall shrinkage, bumps, scuffs and other blemishes commensurate with age. The trunk door is locked and we do not have a door key.Clock has a pendulum, two weights and a winder. Condition Report Disclaimer

A FRENCH EMPIRE ORMOLU FIGURAL MANTEL CLOCK 'AMOR'BLANC FILS, PARIS, EARLY 19th CENTURYThe circular eight-day countwheel bell striking movement with anchor escapement regulated by disc bob pendulum incorporating silk suspension regulation, the circular white enamel Arabic numeral dial signed Blanc Fils, Palais Royal to centre within vertically orientated numeral to chapter, with blued steel moon hands set within an engine-milled bezel, the case modelled with a figure of winged amor holding an arrow in his left hand and gesturing his right forefinger to his lips whilst leaning against an architectural pedestal housing the clock dial, the fascia with a mount cast with twin lovebirds supporting a banner inscribed AMOR to lower margin beneath anthemion scroll infill to upper quadrants, the top applied with Amor's quiver and bow, the rectangular platform base decorated in relief with scene of Amor and Cronos abord a swan-bow boat and the sides with rosette-centred laurel mounts, on compressed bun feet.32cm (12.5ins) high, 24cm (9.5ins) wide, 13cm (5ins) deep. Blanc Fils are recorded in Britten F.J. Old Clocks and Watches and Their Makers as working from Palais Royal, Paris, 1807-25.Condition Report: Movement is intact and with no visible evidence of alteration or noticeable replacements. The mechanism is in dirty/neglected condition however the going train will beat and the strike will operate when encouraged (but is intermittent when hands are moved forward). Generally the movement is dry/gummed-up hence gentle clean/service is required. The dial has some small shallow chips around the winding holes otherwise is in fine condition. The case is generally in fine original condition retaining strong original gilding exhibiting light to moderate gilt wear to edges/extremities. Amor's bow has a repaired break and is presently able to pivot on its fixing hence a slight 'rub' mark caused by the tip of the bow moving across the top of the platform.Clock has a pendulum and a winding key.  Condition Report Disclaimer

A SWISS RENAISSANCE IRON CHAMBER CLOCKUNSIGNED, CIRCA 1600The two train weight-driven countwheel bell movement with verge escapement regulated by horizontal balance contained between angled extensions of the front and rear pivot bars, the strike train with single arbor warnless locking released via nag's head engaging with a pin fitted to the rim of the going train greatwheel and overlift provided by a shaped cam cut with a slot for locking, both trains pivoted between iron vertical bars which locate via tenons into slots cut into a horizontal strip at the base, the top secured with another strip terminating with angled ends forged with pierced tenons passing through slots in the uprights and secured by wedges, the iron box-form case with a single lugged bell supported within domed bearer decorated with forged iron flower buds, the front with visible hour wheel and gilt painted arrow-shaped hand reading against a cream painted chapter ring with Gothic Roman numerals within upper and lower borders polychrome painted with symmetrical bird inhabited foliate scrolls on a chocolate brown ground beneath moulded gilt band and panel painted with an owl within conforming field, the sides with hinged doors secured by sprung clasps and painted with conforming large floral sprays, the rear with forged hanging hoop and spurs, (escapement restored, case decoration refreshed, left side door probably replaced, lacking weights and lines).26.5cm (10.5ins) high, 12cm (4.75ins) wide, 13,5cm (5.25ins) deep. The general construction and layout of the current lot can be directly compared to a spring-driven example illustrated in Bassermann-Jordan, Ernst von THE BOOK OF OLD CLOCKS AND WATCHES (English version translated by H. Alan Lloyd) on page 203 which is described as probably made in Zurich about 1630-40. The basic construction of the movement frame (formed essentially as a vertical rectangular loop around the movement) has its roots in the earliest form of domestic striking clock and can be directly compared with a clock dating to around 1500 illustrated in Muhle, Richard and Vogel, Horand M. Alte Uhren (Verlag Georg D.W. Callway, Munchen 1976) on page 152 (figure 256).Condition Report: Movement - All wheelwork with the exception of the escapewheel and balance appear original, the greatwheels have four crossings, all other wheels have three, all arbors except the escapewheel arbor are faceted. Both pulleys appear to be replacements mounted onto the original greatwheel arbors. As catalogued the current escapement is a restoration. Evidence in the movement bars and backplate indicate that the clock was once fitted with an anchor escapement with pendlum swinging to the rear. In order to allow clearance for the anchor pallet arbor the fly was moved to one side and pivoted between extension plates riveted to the centre and rear movement bars, the fly has now been returned to its original position and the later plate extension pieces removed (leaving stopped rivet holes and other witness marks). There is a mall keyhole shaped hole and two small rectangular slots (one in the front movement bar, the other to the top bar just in front of the balance arbor), the purpose of these is unknown but unlikely to be from an alarm mechanism due to lack of space for lines to pass beneath hence most likely to be from another escapement configuration fitted to the clock at some time (possibly French vertical verge and pendulum arrangement as often seen on Comtoise region clocks?). The nag's head lifting piece, locking detent and arbor are replacements however the curved pivot carriers fitted to the from and rear movement bars appear original. The hour wheel appears original but is now on a replacement arbor/pivot and is driven by a replacement four-prong pinion of report fitted to the original greatwheel arbor. Case - Dial plate appears original and is forged in two sections joined behind the moulding above the chapter ring and is in turn rivetted to two forged uprights each with angled brackets applied with threaded stub at each end (for fitting to the case top and bottom plates). The dial has been repainted and the rear of the plate has also been cleaned and painted. The rear of the case also appears original and is made from two relatively thin guage metal vertical panels which overlap and are rivetted together. This is then fitted onto two metal bars as pof the dial. The rear of the backplate has two horizontal strips rivetted which carry the hanging hoop and spurs and are formed into hinge knuckles for the side doors ar each end.  The backplate appears to retain old surface and has two filled (with lead solder) holes left over from the earlier conversion to anchor escapement (from pallet arbor and pendulum backcock). The left hand door is a replacement made from poorly matched iron plate with curious texture (left over from the panels earlier use) and does not fit well. The right hand door appears original and retains its clasp. the baseplate also appears to be original and is fitted with replaced pivot arm (to transfer motion from the strike hammer pins to the vertical hammer pivot) to original pivot forged to the underside of the plate. Their are a few small redundant holes to the baseplate suggesting that the clock may have been located onto a wall bracket at sometime.  The top plate is almost certainly a replacement made from salvaged iron plate as it is thicker gauge than the rest of the case and three of the four surfaces (and the various holes in the plate) appear relatively fresh. The bell support appears to have age and seems to be made from forged rather than sheet metal however it is difficult to be entirely sure whether it is original or not. The bell is a replacement with the lugged fitting being applied (via a screw from beneath) to a bell of standard construction. The clock is missing two of the eight case screws (which hold top and bottom plates to frame uprights). Clock is currently not in working order due to slightly loose balance top pivot and dislocated pawl spring to the winding pulley click. No doubt other minor fettling will also be required to bring it back to working condition.  There are weights or line present with the clock. Condition Report Disclaimer

A BURR WALNUT QUARTER-CHIMING EIGHT-DAY LONGCASE CLOCK WITH MOONPHASEALEXANDER GIROUST, LONDON, CIRCA 1720 AND LATERThe five pillar triple train movement with anchor escapement regulated by wood-rod seconds pendulum, chiming the quarters on a graduated nest of eight bells and sounding the hour on a further larger bell, the 12 inch brass break-arch dial with calendar aperture and subsidiary seconds dial to the matted centre within applied silvered Roman numeral chapter ring with fleur-de-lys half hour markers and Arabic five minutes to outer track incorporating Strike/Silent and Chime/Silent switches to upper quadrants, with scroll pierced steel hands and female mask centred scroll cast spandrels to angles, beneath arch with rolling moonphase incorporating age of the moon to the circumference of the disc and foliate scroll engraved lunettes beneath herringbone infill and applied silvered plate engraved ALEXANDER GIROUST, LONDON to the upper margin, the break-arch case with generous cavetto cornice and scroll decorated blind fret frieze over unusual bolection moulded hinged glazed dial aperture flanked by free-standing Doric columns with brass caps and bases, the sides with brass fish-scale grille inset break-arch apertures and conforming quarter columns set against bargeboards at the rear, the trunk with caddy moulded break-arch door quarter-veneered ion fine burr walnut within double-line strung and herringbone banded borders, the surround with conforming line inlay and the sides also herringbone banded, the base with concave top moulding and centred with a raised caddy-moulded double-line and herringbone banded rectangular panel to front, the sides with herringbone border, on moulded skirt with squab feet.234cm (92ins) high, 53cm (21ins) wide, 28.5cm (11.25ins) deep. Alexander Giroust is recorded in Baillie, G.H. Watchmakers & Clockmakers of the World as working in London 1728-39. 

Y A REGENCY BRASS INLAID MAHOGANY LONGCASE CLOCK THE DIAL INSCRIBED FOR J. CHADWICK, LONDON, CIRCA 1820The five pillar rack and bell striking movement with anchor escapement regulated by seconds pendulum, the 12 inch circular cream painted Roman numeral dial with subsidiary seconds and inscribed J. CHADWICK, G'T BATCH ST., LONDON to centre, with scroll pierced blued steel hands and SILENT/STRIKE selection switch to the edge of the plate at twelve o'clock, the lancet-shaped case with cavetto cornice over rosette-centred brass line panel infill around the hinged glazed circular cast brass bezel flanked by slender reeded pilasters to angles, the sides with circular glazed apertures, the trunk with concave throat over flame-figured caddy-moulded lancet-shaped door with rosette decorated brass line panel infill to upper quadrants and flanked by fluted quarter-columns set on ebony strung plinths, the base with concave top moulding over reeded ebony bordered geometric panel to fascia, on moulded double skirt incorporating integral bracket supports with shaped apron between.204.5cm (80.5ins) high, 49cm (19.25ins) wide, 23cm (9ins) deep. 

A CHARLES II MINIATURE BRASS LANTERN TIMEPIECE WITH ALARMSIGNED FOR JOHN KNIBB, OXFORD, CIRCA 1680The going train with verge escapement regulated by short bob pendulum swinging outside of the frame to the rear and motionwork for two hands, the rear with alarm mechanism incorporating verge crown wheel driving vertically pivoted yoke-shaped hammer fitted to the backplate and sounding on the inside of the bell mounted above, the dial with rose-decorated alarm disc within a band of engraved scrolling flowering foliage issuing from a three-petal bloom to the lower margin to centre, within applied Roman numeral chapter ring with squat fleur-de-lys half hour markers and punched dot minute marks to outer track, the frame with one-piece corner castings formed as Doric columns beneath vase finials with collar-turned shoulders, the front and sides applied with symmetrical pierced cast and engraved brass dolphin pattern frets with the front incorporating inscription John Knibb to the lower margin, beneath domed bell bearer capped with a conforming vase finial, with brass side doors, twin iron hanging hoops and spurs to rear, on integral ball-shaped feet, (with probable restoration).23cm (9ins) high, 9cm (3ins) deep, 10.5cm (4.5ins) deep. John Knibb was born in 1650 and was apprenticed to his older brother, Joseph, in around 1664. When Joseph moved to London in 1670 to set up business (presumably in the workshop inherited from his uncle, Samuel) John took on the Oxford workshop gaining the Freedom of the city on payment of a fine in 1673. Joseph Knibb retired in 1697 selling up most of his workshop before moving to Hanslop, Buckinghamshire where he made a few clocks prior to his death in 1711. John Knibb became a high profile figure within the City of Oxford twice becoming Mayor, he continued in business until his death in 1722. Due to the comparative rarity of clocks signed by John Knibb it has been suggested that his workshop may have generally served to supply Joseph's larger concern in London. The strong similarities between John's best work and those signed by Joseph would certainly support this view. However it is also clear that John was a high profile tradesman in the City of Oxford who trained no less than ten apprentices, therefore it is perhaps more likely that, although the two workshops were closely connected, they generally worked separately to supply clocks to differing groups of clients. The present lot would appear to conform with the earlier group of miniature lantern clocks produced both during Joseph's time in Oxford (up to around 1671) and subsequently by John Knibb. These clocks are generally characterised by their one-piece corner castings incorporating well-detailed vase finials decorated with a distinctive incised band just beneath the shoulder. Latterly (perhaps from around 1680) the Knibb workshops generally adopted different castings which incorporated simple small concave sided projections for the finials and button feet. Several examples with the 'earlier' type of frame are illustrated in White, George English Lantern Clocks on pages 257-58 (Figures V/108-11) and again in detail on page 261 (Figure V122), whilst an example of the later type is featured on the front cover of Hana, W.F.J. English Lantern Clocks. Although the current timepiece appears to utilise the earlier type of castings they have perhaps been more tightly turned/finished a little less generously than usual.In conjunction with the vase finial frame castings the Knibb workshops invariably used dolphin pattern frets which are described by George White as a being 'wafer thin' and, more often than not, carried the signature along the lower border. The frets on the current lot can certainly be described as thin, delicate castings. The engraving to the dial centre is very close to that of the later-type frame example illustrated by Hana, however the squat fleur-de-lys half-hour markers appear identical to those on a clock, this time with the earlier vase finial frame castings, by John Knibb illustrated in Lee, Ronald A. The Knibb Family * Clockmakers on page 162 (Plate 176). From these details it would be perhaps appropriate to suggest that the present timepiece was made as the earlier vase finial castings were being phased-out in favour of the later simpler frame.The two-handed configuration of the present timepiece is unusual but not unheard of with regards to Lantern clocks in general. Indeed two-handed clock (albeit quarter chiming) Lantern clock by John Knibb is illustrated by George White on page 260 (Figure V/117). This clock also has 'dot' minute markers (as part of the outer track). There is a possibility that the present clock has been converted to two-handed configuration, if this is the case then it has been executed to a very high standard. Finally, when the considering the present the clock as a whole, other details typical of those originating from the Knibb workshops can be seen; most notably the shaping of the escapement top potance and backcock, as well as the presence of two hanging eyes fixed to the rear of the top plate.Condition Report: Movement is in relatively clean working condition with delicate wheelwork commensurate with the Knibb workshops. The pivot holes show no evidence of re-bushing or noticeable wear; the pinions also exhibit little in the way of wear. Due to the lack of wear evident we cannot rule-out whether the train is a restoration however it is not unusual for such timepieces to exhibit little use as historically they were often only used occasionally (whilst travelling). There is no obvious evidence that the greatwheel arbor has been modified to allow combined hour and minute gears to be fitted (rather than just having a square for the pinion of report) hence it would appear that the train was made for two-handed motionwork. The alarm mechanism is in similar condition to the going train - ie. complete and well-made but shows negligeable wear.The dial is in fine original condition and, as catalogued, conforms with those seen on other examples emanating from the Knibb workshops. The alarm disc is most likely a restoration. The hands are very well made but are somewhat 'clean' in appearance. The 'dot' minute markers to the outer edge of the chapter ring do not appear to have been added recently hence there is a strong argument that they were executed at the time the chapter ring was made. The frame is in sound original condition however the shaft to the front left hand upright has an inserted section around 1.5 inches long let-in. This is most likely to repair a casting fault at the time of making and is mostly obscured by the chapter ring and side door. The rear left hand finial is a replacement. The top and bottom plates exhibit no evidence of alteration. The frets appear original although the left-hand side fret is not fully finished. The bell bearer is probably a replacement and the bell itself has been repaired (although it rings fine). The side doors appear correct, the left-hand door has a slight casting fault. The hanging hoops and spurs appear a little 'clean' hence may be restorations although the threads securing the spikes are correctly hand cut and show signs of age (slight corrosion and wear). Timepiece is complete with rope lines and weights. Condition Report Disclaimer

A GEORGE III BRASS MOUNTED MAHOGANY BRACKET CLOCK THE DIAL BEARING INSCRIPTION FOR RIGBY, LONDON, CIRCA 1800The five pillar twin fusee bell striking movement now with anchor escapement regulated by lenticular bob pendulum, the backplate with bright-cut geometric border-engraved decoration, the 7 inch circular cream painted Roman numeral dial now inscribed Rigby, CHARING CROSS, LONDON, beneath 1801 to centre and with delicate pierced steel hands, the break-arch case with hinged brass carrying handle to the brass-fillet moulded single pad top panel over complex moulded cornice, the hinged front panel fitted with convex glazed stepped-ogee cast brass bezel over brass fish scale lower quadrant frets flanked by brass edged front angles, the sides with conforming arched brass frets and the rear with break-arch door set within the frame of the case, on cavetto moulded skirt base with brass ogee bracket feet.40.5cm (16ins) high with handle down, 28cm (11ins) wide, 19cm (7.5ins) deep.Condition Report: Evidence in the plates (a small group of vacant haoles) indicates that the movement was originally made with verge escapement regulated by short bob pendulum. The conversion to anchor escapement appears to have been executed early in the clocks life with minimal alteration to the plates hence could be re-converted back to verge leaving little evidence of the present escapement if desired. The bell stand has been repaired and there is a spere hole to eh left hand margin of the backplate left over from the holdfast hook for the verge bob pendulum. The movement otherwise appears to be in sound working condition however it is a little dirty/neglected hence a gentle clean service is advised. The dial has been refinished hence we cannot rely on the inscribed name (Rigby) being the maker of the clock; the finish exhibits light wear and scratching mainly around/near the winding holes. The hands are of nice quality and appear free of faults.The case is in good original unrestored condition. The veneer to the arch top is in fine condition with minimal shrinkage, the veneer capping the pad has slight wear to one corner. The front door has a filled key escutcheon and the carcass has filled recess from a lock being previously fitted; the door is now secured via a tongue engaging with a lock positioned to the left hand side of the case (with key-hole cut just in front of the sound fret). The right-hand side has a filled hole almost certainly for a trip=repat cord which is no longer in use. The rear door has some chipping and a patch repair to the veneer edge overlap and the lock is a little loose. The brass mounts (handle, mouldings, frets, bezel and feet) are fairly heavily tarnished/discoloured; case otherwise in very sound original condition with relatively few age-related faults and is of good colour.Clock has a pendulum, winder and a case key.  Condition Report Disclaimer

A FINE AND HOROLOGICALLY SIGNIFICANT JAMES I 'FIRST PERIOD' LANTERN CLOCKWILLIAM BOWYER, LONDON, CIRCA 1620The separately wound trains with iron-cheeked pulleys to the great wheels, the going train with reinstated verge escapement regulated by horizontal balance oscillating above the frame top plate, the strike train sounding the hours on a lugged bell mounted above the frame via an iron countwheel with overlift provided by an iron-walled hoop wheel cut with a single slot, the dial finely engraved with a large chrysanthemum bloom over twin entwined stalks set within a field of scrolling flowering foliage to centre, within applied narrow silvered Roman numeral chapter ring incorporating floating asterisk half hour markers and concealing fine signature William Bowyer of Lon Fecit engraved in a downward curve to the plate behind the lower part, with fine sculpted steel hand and foliate engraved infill matching that of the centre occupying the upper quadrants and the lower margin, the frame with finely turned generous Doric column corner posts beneath distinctive ovoid vase finials with banded waists, the front and sides applied with symmetrical scroll pierced cast brass frets with the front incorporating foliate engraved detail, beneath domed iron bell bearer capped with a conforming vase finial incorporating pinned plinth upstand for securing the lugged bell, with brass side doors and the rear with iron hanging hoop over spurs applied to the brass backplate, on collar-turned ball feet.40cm (15.75ins) high, 15cm (6ins) wide, 18.5cm (7.25ins) deep.William Bowyer is recorded in Loomes, Brian Clockmakers of Britain 1286-1700 as the son of Ralph Bowyer (yeoman of Warfield Berkshire) who is believed to have been married to Alice Mansworth in 1590. William was probably born around this time and by 1616 was a member of the Pewterers' Company when he took-in Thomas Taylor (son of Ralph Taylor, a milliner from Halesowen, Shropshire) as an apprentice. Bowyer took-in no less than five further apprentices prior to the formation of the Clockmakers' Company in 1631, including John Pennock (son of William Pennock of Guisborough, Yorkshire) in 1620. Although he subscribed £5 towards its charter and was made free of the City in 1630, William Bowyer did not apparently join the Worshipful Company on its establishment the following year.Bowyer is thought to have been first married to Margery Barlow of Litchfield, Staffordshire, however, by 1631 he was married to Prudence with whom he had five children (three of which sadly died in infancy). By 1638 Bowyer was living in the parish of St. Andrew Undershaft, he took-in Joseph Jackson (through Thomas Dawson) as apprentice that year and during the following decade took-on at least four more, this time through the Clockmakers' Company. One of these apprentices was Nathanial Allen (probably around 1641/2); Allen subsequently married a Phillipa Bowyer in 1646 hence became related to William through marriage.In 1640 William Bowyer was invited to become an Assistant of the Clockmakers' Company, however it appears that he was reluctant to serve the Company as in July 1642 he gave 'a great chamber clock' in return for excusal from any further duties. Nevertheless he became an Assistant in 1651 and a Warden in 1653 the year of his death.The present clock belongs to a group of less than half-a-dozen surviving particularly early examples made by Bowyer either just before or around 1620. Of the others the first (dated 1617) was sold at Bonhams, London sale of Fine Clocks 11th July 2018 (lot 60 for £43,750) and the second is illustrated in Loomes, Brian LANTERN CLOCKS & Their Makers on page 79 (Figures 7.1-4). Another is illustrated in White, George English Lantern Clocks onpage 101 (Figure II/125 showing movement only), and possibly a fourth on page 113 (Figure II/145).All of the above examples share the same frame castings which are very closely related to those used by the earliest of English Lantern clock makers, brothers Robert and Thomas Harvey. These frames are characterised by having well-proportioned Doric column corner posts surmounted by slightly shouldered ovoid vase finials each decorated with a ring around the waist beneath a disc knop. The ball feet are also cast with a collar matching that of the finials. Indeed when the frame of the present clock is compared with that of an example by Thomas Harvey illustrated in Loomes, Brian LANTERN CLOCKS & Their Makers it can be seen that the castings differ only in very slight detail.In addition to sharing the same design of frame castings it has been noted by Brian Loomes in his article William Bowyer, an exciting and important discovery published in 'Clocks' magazine, June 2018 (pages 9-12) that the movement pivot bar castings follow the same form as those used by Robert and Thomas Harvey. This suggests that these castings may have a common source, most likely the Harvey workshop. It is therefore likely that, during his formative years, William Bowyer had some form of connection with this very important workshop. From the images available it can be seen (with the possible exception of the last clock illustrated by White on page 113) that this group of clocks are all essentially identical with regards to the layout and detailing of the movements. All have iron countwheels, iron-walled hoopwheels, straight hammer checks and iron cheeks to the pulleys (where the originals survive). They also share the same frets hence only essentially differ in the treatment of the dials, and whether an alarm was originally fitted. These inherent similarities suggest, that even at this very early date, a degree of standardisation was being adopted mostly through the use of common castings.The present clock is noticeably well finished with each of the cruciform movement pivot bars having decorative scroll-shaped detailing just above the hammer arbor pivots. This attention to detail is carried forward to the dial which exhibits fine albeit unusual foliate decoration to the entirety of the dial centre. It is perhaps interesting to compare this decoration with that of Bowyers celebrated 'Memento Mori' great chamber clock of 1623 illustrated in Bruce, W.F. EARLY ENGLISH LANTERN CLOCKS 1600-1700 (2013) on page 17. Although the decoration of this larger clock lacks a large flowerhead (or any other large single element) the foliate infill has a similar feel to that of the present clock, albeit in a perhaps slightly more developed form incorporating scrolls and loops to the design.Please see the page-turning catalogue to continue reading the final part of this footnote. 

AN AUSTRIAN EBONISED SMALL TABLE CLOCK WITH CONCENTRIC CALENDAR AND TRIP-HOUR REPEATTOBIAS FLASCHGE, VIENNA, LATE 18th CENTURYThe four pillar twin standing barrel thirty-hour bell striking movement with verge escapement regulated by short-bob pendulum, the 5 inch brass break-arch dial applied with convex white enamel hour disc with concentric calendar to inner track and vertically orientated Arabic hour numerals, with scroll-pierced gilt hands and bead-bordered foliate cast spandrels to angles beneath arch centred with enamel plaque signed Tobias, Flaschge, in Wien over arched false-bob aperture and flanked by foliate engraved infill, the inverted bell-top case with hinged brass carrying handle flanked by hounds head finials over giltwood foliate scroll decoration, flambeau urn finials and complex top mouldings, the front with rectangular door applied with gilt ripple-mouldings to the dial aperture beneath engraved brass upper quadrant frets and enclosing conforming ripple-moulded border to the dial mask, the sides with lozenge-shaped mirror panels over shaped-top rectangular glazed apertures incorporating upward-curved lower edges, the rear with rectangular glazed door, on stepped moulded skirt base with leaf-cast brass feet.42cm (16.5ins) high with handle down, 23.5cm (9.25ins) wide, 13cm (5ins) deep. Tobias Flaschke is recorded in Baille, G.H. Watchmakers & Clockmakers of the World as becoming a Master in Vienna, 1788. 

A GEORGE III BRASS MOUNTED MAHOGANY BRACKET CLOCK WITH TRIP-HOUR REPEATPERIGAL AND DUTERRAU, LONDON, CIRCA 1800The five pillar twin fusee bell striking movement with anchor escapement regulated by lenticular bob pendulum and signed Perigal & Duterrau, London within an elliptical reserve to the wheat ear border engraved backplate, the 7 inch circular cream painted convex Roman numeral dial with pierced brass hands, the break-arch case with hinged brass carrying handle applied to a curved brass fillet-edged pad and complex upper mouldings, over opening front fitted with circular convex-glazed ogee moulded cast brass bezel to the dial aperture and with brass fish scale sound frets to lower quadrants, the sides with conforming arched brass sound frets and the rear with arch glazed door set within the frame of the case, on cavetto moulded skirt base with brass ogee bracket feet.33cm (13ins) high with handle down, 28cm (11ins) wide, 19,5cm (7.75ins) deep. The partnership between John Perigal (from the celebrated family dynasty of clockmakers founded in the 1720's by Claude Perigal) and John Duterrau was formed prior to 1799 as they were granted a Royal warrant as a 'Watchmaker in Ordinary' to George III on the 20th February of that year. The partnership is subsequently noted as working from 57 New Bond Street, London 1802-05 and then from 62 New Bond Street 1810-40.  

A GEORGE III MAHOGANY SMALL TABLE CLOCK CASEANONYMOUS, LATE 18th CENTURYWith hinged brass carrying handle to the bell-top superstructure and double cavetto top mouldings over hinged front with break-arch glazed dial aperture measuring 6 by 8.375 inches and scroll-pierced frets to upper quadrants, the sides with arch-glazed apertures and the rear with break-arch glazed door set within the frame of the case, on cavetto moulded skirt base with moulded squab feet.44cm (17.25ins) high with handle down, 24cm (9.5ins) wide, 18cm (7ins) deep. 

A QUEEN ANNE EIGHT-DAY LONGCASE CLOCK WILLIAM TOMLINSON, LONDON, CIRCA 1700-10The five finned pillar inside countwheel bell striking movement with anchor escapement regulated by seconds pendulum, the 11 inch square brass dial with subsidiary seconds dial, ringed winding holes and calendar aperture to the matted centre within applied silvered Roman numeral chapter ring with cruciform half hour markers, Arabic five minutes to outer track and signed W. Tomlinson, London to lower margin, with scroll pierced steel hands and twin cherub and crown cast spandrels to angles, in a case now veneered in figured walnut with carved winged cherub head centred swan-neck crest over ogee cornice, scroll pierced fretwork frieze and Solomonic three-quarter columns to hood door, the sides with rectangular glazed panels and conforming quarter columns set against bargeboards at the rear, the trunk with concave throat over brass circular lenticle centred line bordered book-matched burr veneered trunk door, the sides with conforming line borders, the plinth base with ogee top moulding over panel veneered front and moulded skirt, (the case originally ebonised).206cm (81ins) high excluding later crest, 218cm (86ins) overall, 38cm (15ins) wide, 25cm (10ins) deep. William Tomlinson is recorded in Loomes, Brian Clockmakers of Britain 1286-1700 as a Quaker born circa 1673 and made a Free Brother of The Clockmakers' Company in July 1699. He is said to have worked at the Dial and Three Crowns in Birchin Lane, near the Royal Exchange, London and later at a premises with the same sign in White Hart Court, Gracechurch Street. Amongst Tomlinson's apprentices was James Snelling from 1703; Hodges died in 1750 aged around 77.Condition Report: Movement appears fundamentally original, is complete and in in clean working condition with some visible rebushing and re-pinioning. The escapement pallets may be original but reworked, the escape wheel is probably a service replacement.The dial is in clean condition, the hands appear original but the minute hand is currently fitted upside down.The movement is fitted to an old oak seatboard which may be original but is missing a section from the rear right hand edge. The seatboard rests directly onto the cheek uprights of the case however there is a possibility that the latter have probably been cut down hence we would suggest that the movement and dial are probably not original to the case.The case has an ebonised pine carcass hence would have most likely been an ebonised case when first made. The walnut veneers, crossgrain mouldings and hood columns are most likely mid 20th century; the cresting may be later still. The base has also almost certainly been rebuilt as the lower third of the backboard has been replaced and the side uprights of the case do not extend all the way into the base. Generally case is presentable with only minor bumps, scuffs, shrinkage and wear.Clock is complete with pendulum, pair of weights, case key and crank winder. Condition Report Disclaimer

Y A FINE WILLIAM AND MARY OYSTER OLIVEWOOD AND FLORAL MARQUETRY EIGHT-DAY LONGCASE CLOCKDANIEL LE COUNT, LONDON, CIRCA 1685-90The five finned pillar outside countwheel bell striking movement with plates measuring approximately 7.25 by 5 inches and anchor escapement regulated by seconds pendulum, the 10 inch square brass dial with ringed winding holes, conforming decoration to the subsidiary seconds dial and scroll border-engraved calendar aperture to the finely matted centre within applied silvered Roman numeral chapter ring with stylised fleur-de-lys half hour markers and Arabic five minutes within the outer minute track, with fine scroll-pierced and sculpted blued steel hands, winged cherub head cast spandrels to angles and engraved Daniel Le Count Londini to lower margin, the case with architectural ogee moulded cornice incorporating swollen crossgrain frieze and ebonised mouldings over fixed glazed dial aperture flanked by opposing ebonised Solomonic twist three-quarter columns, the sides with rectangular windows and conforming quarter-columns set against bargeboards rising past the lintel to meet the cornice overhand at the rear, the slender trunk with convex oyster olivewood veneered throat moulding, over 42 inch rectangular door centred with an oval lenticle and with two break-arch bordered marquetry panels decorated with bird inhabited floral sprays and scrolling foliage into an ebony ground within an oyster olivewood field, further incorporating conforming shaped marquetry quadrant panels to upper corners and contained within an inset line border edged with ebonised half-round mouldings, the sides veneered with two panels of repeating oysters within crossbanded surrounds, the base with stepped ogee top moulding and fronted with conforming rectangular marquetry panel decorated with floral blooms into an ebony ground over ebonised bun feet.197cm (77.5ins) high, 47cm (18.5ins) wide, 26.5cm (10.5ins) deep. Daniel Le Count is recorded in Loomes, Brian Clockmakers of Britain 1286-1700 as most likely being a Huguenot refugee from France who was first made free of the Haberdashers' Company before becoming a Free Brother of the Clockmakers' Company in 1676. He took on at least five apprentices including one through Nicholas Coxeter (Charles Ekins in 1677) and two through William Speakman (James Way in 1681/2 and Daniel Lefebure in 1686). Daniel Le Count is thought to have married twice with two children, Daniel and William, born to his first wife, Mary in 1676 and 1677 respectively. He married his second wife, Ursula, at St. James's, Dukes Place in 1681/2 with whom he had a daughter, Judith. In 1695 the Le Count family were recorded as living in the parish of St. Bartholemew by the Exchange and, in 1697, he signed the Clockmakers' Company oath of allegiance. Daniel Le Count attended council meetings until 1705; he died in 1738 and was buried at Spitalfields.Condition Report: The movement is in relatively clean working condition and appears all-original with no visible evidence of alteration or noticeable replacements. The collet to the third wheel of the going train has been 'turned down' probably to allow the wheel to be moved along the arbor a fraction so mitigate wear to the next pinion in the train. Indeed pinions show overall evidence of historic wear however this has generally been mitigated by moving the wheels along their arbors a fraction so that they mesh with unworn parts of the pinions - an accepted practice in the conservation of early movements hence does not detract from the clock in anyway. The dial is also in good original condition. The matting is particularly fine, there is a visible rivet mark next to the calendar aperture (for a calendar wheel carrier post) and the two lower dial feet attachment points are just visible within the inner edge of the chapter ring. The silvering to the chapter ring has overall light to moderate patchy discolouration/tarnishing. The hands are finely worked and in good condition, the spandrels are also well finished and appear original. The movement is fixed on what appears to be the original seatboard which in-turn rests directly onto the cheek-uprights of the case indication that the movement and dial are most likely original to the case. There is a movement securing bracket fitted tom the movement backboard which corresponds to a bracket on the rear of the movement however the securing thumbscrew in now missing.The case appears to be in fine original condition although it is likely that it has seen some cosmetic attention to the finishes at some point in the past. The hood is in original condition (no evidence of the front being cut for a door) retaining the grooves for the rising action to the rear edges. The structure exhibits age-related shrinkage as do the veneers and crossgrain mouldings. There is a small loss to the front right-hand corner of the frieze cushion mouldings as well as to the veneer lining the edge of the left hand rear bargeboard otherwise faults are very much limited to age related shrinkage and a few minor historic bumps and scuffs. The backboard has replacements to each side behind the hood incorporating 'tongues' for the rising action; it is possible that at some point the tongues had become broken or were removed to allow the hood to be removed by drawing forwards. There is a spoon locking mechanism present as well as a sprung latch to secure the hood in raised position - both of these appear genuinely old and undisturbed so are most likely original.The trunk and base are in similar condition to the hood with historic shrinkage and movement but no visible evidence of alteration or replacements. The backboard continues down to border the lower edge of the base and, with the exception of having a baton screwed to the inside lower edge, appears undisturbed. The structure of the base also appears undisturbed; the fascia has horizontal shrinkage cracking but no noticeable losses to the marquetry veneers. The trunk door retains original locks and hinges and has slight shrinkage to the joints between the clamps and the board to both the upper and lower margins; this is to be expected and again there are no visible losses to the veneers. The lentical glass is cracked. The sides have a few small historic veneer patch repairs to the rear edge otherwise faults are limited to age-related shrinkage. The front door has some blooming to the finish. The marquetry also has reddy-brown highlights which are probably an old attempt to add contrast to the finish; there is raised 'roughness' to the joints within the marquetry indicating that the present surface has serious age hence any refinishing/cosmetic restoration was undertaken a long time ago (the plinth veneers are in conforming condition).Generally the present clock presents as a fine original example that appears to want no more than some attention to the finish of the case and a gentle service to the movement.Clock has a pair of brass cased weights, pendulum, a crank winder and a case key. Condition Report Disclaimer

AN UNUSUAL GEORGE III EIGHT-DAY LONGCASE CLOCK MOVEMENT AND DIAL WITH 'ROCKING EYE' AUTOMATONSAMUEL LINES, LUTON, LATE 18th CENTURYThe five pillar rack and bell striking movement with anchor escapement for regulation by a seconds pendulum, the 11.75 inch single sheet engraved brass Roman numeral dial with subsidiary seconds dial, calendar aperture and signed Samuel Lines, Luton to centre, with Arabic five minutes to outer track and twin bird and urn cast spandrels to angles, the arch painted with portrait of a turbaned gentleman with 'rocking eye' automaton matching the motion of the pendulum via painted inserts connected to the pallet arbor behind, (unrestored; hands, pendulum, weights and pulleys lacking).41.5cm (16.375ins) high, 30cm (11.875ins) wide, 15cm (6ins) deep. Samuel Lines of Luton does not appear to be recorded in any of the usual clockmaker's directories. 

A GEORGE II TORTOISESHELL JAPANNED EIGHT-DAY LONGCASE CLOCK WITH ROCKING FIGURE AUTOMATONPETER KING, LONDON, MID 18th CENTURYThe five pillar rack and bell striking movement with anchor escapement regulated by seconds pendulum, the 12 inch brass break-arch dial with subsidiary seconds dial, calendar aperture and signature plate engraved Peter King, LONDON to the matted centre within applied silvered Roman numeral chapter ring with fleur-de-lys half hour markers and Arabic five minutes to outer track, with scroll-pierced blued steel hands and female mask and scroll cast spandrels to angles, the arch with circular aperture revealing a engraved silvered brass figure of Chronos rocking back and forth with the motion of the pendulum against a painted starry sky background, the silvered border inscribed TEMPUS FUGIT flanked by dolphin case mounts, the mottled iron-red and dark brown/black japanned case with moulded cornice and gilt lattice trellis painted upper quadrant infill over hinged glazed dial aperture decorated with gilt scrolling decoration and flanked by three-quarter columns to front angles, the gilt foliate spray decorated sides with rectangular glazed apertures and conforming quarter columns set against bargeboards at the rear, the trunk with rosette-centred gilt leaf painted throat over break-arch door decorated in raised polychrome and gilt with oriental figures within a stylised trellis landscape over lion to lower margin, the surround with gilt trellis upper quadrant infill and scroll-banded borders, the sides with large leafy sprays, the plinth base with further figural landscape panel over a tall moulded stepped skirt.221.5cm (87.25ins) high, 54.5cm (21.5ins) wide, 26cm (10.25ins) deep. Peter King is recorded Baillie, G.H. Watchmakers & Clockmakers of the World as working from Great St. Andrews Street, London 1715-35.Condition Report: Movement is in clean working condition with no visible evidence of alterations and replacements limited to the escape wheel and pallets which are probably 19th century 'service' replacements (due to the originals becoming worn). The dial has some slight patchy discolouration/tarnishing to the silvering and slight wear/rubbing to the background of the rocking figure otherwise appears to be in good original albeit clean condition. The hands are nicely worked and exhibit strong blued finish. The movement and dial retains what appears to be the original seatboard which rests directly onto the cheek uprights of case (which appear undisturbed) hence it is most likely that the movement and dial are original to the case.The case is generally in sound original condition with some evidence of relatively light cosmetic restoration. The hood probably originally had a caddy superstructure; the upper quadrant panels and the columns are almost certainly well-executed restorations/replacements. The backboard is made from two boards butt-jointed together; this joint has opened hence there is an open crack from top to bottom necessitating batons to be screwed to the rear of the case. The door retains its original lock and hinges. The base has moulded skirting applied over the bottom two inches or so of the decorated fascia (obscuring the lower part of the panel) however the rest of the panel appears to survive behind the skirting.Faults to the case are otherwise very much limited to minor bumps, scuffs, shrinkage, wear minor repairs and other blemishes commensurate with age and use.Clock is complete with pendulum, two weights, case key and crank winder. Condition Report Disclaimer

AN EARLY VICTORIAN EBONISED FIVE-GLASS MANTEL CLOCKMORELAND, CHESTER, CIRCA 1840The substantial six knopped pillar twin chain fusee bell striking movement with anchor escapement regulated by lenticular bob pendulum incorporating holdfast to the movement backplate, the 7.25 inch square silvered brass Roman numeral dial signed Moreland, CHESTER to centre, with pierced steel hands and delicate foliate scroll engraved decoration to spandrel areas, the case with bevel-glazed top panel to the full-width upstand over slender cavetto cornice, the front door with angled silvered brass fillet to the glazed aperture and canted front angles, the sides with rectangular bevel-glazed panels and the rear with rectangular brass grille inset door set within the frame of the case, the base with ogee-outline apron over conforming moulded skirt.37cm (14.5ins) high, 30cm (11.75ins) wide, 18cm (7ins) deep. Thomas Moreland in recorded in Loomes, Brian Watchmakers & Clockmakers of the World, Volume 2 as working in Chester 1834-48. 

A QUEEN ANNE EBONISED THIRTY-HOUR LONGCASE CLOCK WITH ALARMWILLIAM BROCK, AXBRIDGE, CIRCA 1715The substantial posted countwheel bell striking single-handed movement with rectangular section steel uprights and anchor escapement regulated by seconds pendulum, the alarm mechanism positioned to the lower right hand side of the movement and sounding on the hour bell via verge crownwheel and vertically pivoted hammer, the 10 inch square brass dial with generous rose engraved alarm disc to the matted centre within applied Roman numeral chapter ring with cruciform half-hour markers and signed W'm Brock, Axbridge to lower margin, with scroll-pierced iron hand and gilt twin-cherub-and-crown cast spandrels to angles, in an ebonised pine case with box upstand to the domed caddy superstructure and generous ogee moulded cornice over hinged glazed dial aperture applied with parcel gilt three-quarter columns to angles, the sides with rectangular glazed windows and conforming quarter columns set at the rear, the trunk with concave throat moulding over 43 inch rectangular door centred with a brass-edged circular lenticle, on plinth base with moulded skirt.222.5cm (82ins) high, 49.5cm (19.5ins) wide, 29cm (11.5cm) deep. William Brock is recorded in Moore, A.J. THE CLOCKMAKERS OF SOMERSET 1650-1900 as living in Cheddar but working from Axbridge from 1707 until around 1730. From Moore's notes he appeared to principally work as a turret clock maker and repairer; however entries in Dr. Claver Morris's diary indicate that he was a very competent maker as these relate to the 'mending of my repeater' (watch) and the making of 'a very fine Month Clock with a Pendulum of 5 feet long'.Condition Report: Movement appears entirely original and is complete with no visible alterations, significant replacements or losses. The mechanism is dirty/discoloured/patinated but is essentially in working order albeit with some noticeable pinion wear. The dial appears all original but again is in dull/dirty condition with the exception of the spandrels which exhibit strong rich gilding.The seatboard is a replacement hence we cannot offer any assurance with regards to the movement and dial being original to the case although they are a very good match. The case has survived in essentially sound original condition; the domed caddy superstructure is a restoration and the lower nine inches or so of the backboard has been replaced otherwise the case appears fundamentally original but re-ebonised over historic surface worm damage and other historic bumps, scuffs, minor repairs and age related defects.Clock has a weight but no pendulum or case key. Condition Report Disclaimer

A RARE LACQUERED BRASS AND MAHOGANY HAWKSBEE-TYPE DOUBLE-ACTION DEMONSTRATION VACUUM PUMPW. LADD, WALWORTH, MID 19th CENTURYWith twin vertical cylinders formed as squat Doric columns set between further slender column uprights beneath break-arch shaped laminated mahogany superstructure secured with substantial brass screws, enclosing twin racks for the pistons operated via a single pinion mounted on the crank handle arbor, with vase-shaped brass finials and the front with recessed silvered plate engraved W. LADD, Penton Place, Walworth, the base with valve for the take-off pipe running backwards beneath a square stage raised on four Doric column supports centred with a circular brass platform incorporating central fitting fed to the pipe, the rear edge with additional lower smaller platform also connected to the same pipework, on moulded platform base incorporating bracket feet; in original oak box with accessories comprising a Magdeburg sphere, a glass bulb with valve, a syphon gauge, a small stage with central needle-shaped feed, and a manual hand pump with valve, (lacking glass bell-jar).The pump 40.5cm (16ins) high, 40.5cm (16ins) wide excluding crank handle, 26.5cm (10.5ins) deep; the box 40.5cm (16ins) high, 59.5cm (23.5ins) wide, 31cm (12.25ins) deep. William Ladd is recorded in Clifton, Gloria Directory of British Scientific Instrument Makers 1550-1851 as working from several addresses in London 1839-72 including 10 Cleaver Street, Kennington (near Walworth) 1846-47. The design of the present lot was developed by Francis Hawksbee (1660-1713) in around 1705 with the twin cylinder arrangement based upon a pump by Denis Papin (1642-1712) who first devised this arrangement (albeit operated by pulleys and foot treadles) in 1674. 

A GEORGE II WALNUT EIGHT-DAY LONGCASE CLOCKWILLIAM CREAK, LONDON, CIRCA 1740The five pillar rack and bell striking movement with anchor escapement regulated by seconds pendulum, the 12 inch brass break-arch dial with calendar aperture and subsidiary seconds dial to the matted centre within applied Roman numeral chapter ring with Arabic five minutes beyond the minute track, with pierced steel hands and brass twin bird and urn cast spandrels to angles, the arch with circular herringbone border engraved silver signature boss inscribed William Creak, LONDON flanked by dolphin cast mounts, in a break-arch case with generous arched cavetto cornice and fretwork frieze over hinged glazed dial aperture with applied with three-quarter columns to front angles, the sides with break-arch windows and conforming quarter columns set against bargeboards at the rear, the trunk with concave throat moulding over book-matched burr-veneered and herringbone banded break-arch door with complex edge mouldings, the sides with twin crossbanded panels, the plinth base with cavetto top mouldings over burr panel veneered herringbone and crossbanded fascia and a moulded skirt.229cm (90ins) high, 54cm (21.25ins) wide, 26cm (10.25ins) deep. William Creak is recorded in Baillie, G.H. Watchmakers & Clockmakers of the World as a 'fine maker' who worked in London from 1754-63. Other sources indicate that he was working from 1740-75 and his workshop was located in the Royal exchange from 1754. Creak supplied musical and automaton clocks for export to the Middle East and China and often incorporated similar complications into examples made for the domestic market.Condition Report: The movement is complete and appears fundamentally all-original with no visible alteration or noticeable replacements. The mechanism is reasonably clean and working however a precautionary gentle clean/service is advised. The dial is also in good relatively clean unaltered condition with faults limited to some patchy discolouration to the silvering and mellowing of the finishes in general. The movement and dial retain what appears to be the original seatboard however there are packing slips (around ¾ inch thick) hence we cannot offer any assurances that the case is original to the movement and dial although they would seem to be perfectly suited.The hood is in good condition; the frets have been replaced otherwise faults are very much limited to minor historic bumps, scuffs, shrinkage and wear commensurate with age. There are two socket holes to the top suggesting that a pair of finials were fitted at some point. The trunk also is in fine condition with particularly nice figured veneers. The trunk door retains its original lock but the hinges are replacements. The front of the door has some shrinkage cracking to the veneers and there is some visible historic movement/bowing to the frame around the door (does not detract from the clock as is a evidence/result of the genuine age of the piece). The plinth has been restored with replacement veneers with the colour of the burr figured fascia panel being darker than the rest of the case; this probably be improved in the hands of a good restorer/finisher. The backboard has opening to the vertical joint between the two boards which form the panel; two horizontal batons have been applied across the back to further brace the panel.Clock is complete with two weights, pendulum, crank winder and two case keys. Condition Report Disclaimer

A FRENCH EMPIRE ORMOLU FIGURAL MANTEL CLOCKPRE FEN ROUCHOUZE, BORDEAUX, EARLY 19th CENTURYThe circular countwheel bell striking movement with anchor escapement regulated by disc bob pendulum incorporating silk suspension, the circular convex white enamel Roman numeral dial inscribed Pre Fen Rouchouzes, a Bordeaux to centre, with blued steel moon hands set within engine-milled ropetwist decorated bezel, the case cast with a standing figure of a male in Classical dress playing a flute whilst leaning against the arched 'milestone' shaped section housing the movement, surmounted by a broad-brimmed hat and applied with vine-draped musical trophy apron mount beneath the dial, the right hand side with a seated hound and vine harvest tools, the plinth base inset with relief cast panel of a Putto attending sheep over engine-turned bell-shaped feet.31.5cm (12.5ins) high, 23cm (9.25ins) wide, 9.5cm (3.75ins) deep.Condition Report: Movement appears complete and original with no visible evidence of alteration or noticeable replacements. The mainspring for the going train is 'spinning' hence will require repair/replacement before the clock will run; the strike train is in working condition. The dial has some very slight wear around the winding holes and appears to be in restored condition overall; the minute hand has been bent to adjust its position relative to the numerals (can be reversed and necessary adjustment made to the motionwork whilst the mainspring is being repaired). The case is in fine condition with only minor patchy discolouration and very slight edge wear to the gilt finishes. Clock has a pendulum but no winding key. Condition Report Disclaimer

A RARE CHARLES II MINIATURE WEIGHT-DRIVEN CLOCK MOVEMENT AND DIALTHOMAS WAYLAND, FROME, CIRCA 1680The two train thirty-hour countwheel bell striking single-handed movement with plates measuring 3.875 by 3 inches united by four bold baluster-turned pillars pinned at the rear, the going train with verge escapement regulated by a short bob pendulum and the strike train with reversed greatwheel to save space, the 5 inch square brass dial with calendar aperture and signed in stylised scrolling script Thomas Wayland, Froome fecit to the upper part of the dial centre over stylised tulip blooms issuing from a leafy bud beneath, within applied narrow Roman numeral chapter ring with cruciform half hour markers, with steel arrow hand and concentric coursed 'brickwork' engraved decoration to spandrel areas.14cm (5.5ins) high, 12.5cm (5ins) wide, 7.5cm (3ins) deep. Brian Loomes in Clockmakers of Britain 1286-1700 refers to the present movement and dial suggesting that it was made in around 1675. Other than this reference to the current lot there appears to be no other record of Thomas Wayland of Frome. The current lot can be best described as somewhat 'jewel-like' in its scale and quality. The trains are well laid-out with the great-wheel of the strike train reversed to allow the plates to be made as small as possible; the pillars are also formed as boldly-turned balusters and pinned at the rear reminiscent of Edward East. The dial engraving is unusual and particularly pleasing. The radial brickwork design to the spandrel areas mirrors that seen on a lantern clock dating to around 1650 attributed to Thomas Browne of Bristol illustrated in Loomes, Brian LANTERN CLOCKS & Their Makers on page 177 (Figure 10.37); whilst the symmetrical naturalistically rendered tulip sprays are more akin to those decorating a lantern clock dating to around 1670 by Lawrence Debnam of Frome also illustrated by Loomes on page 186 (Figure 11.1).Finally it is tantalising to theorise on the type of case that would have originally housed the present movement and dial. Two options would appear most logical. The first would be a hooded wall case, the second a particularly slender longcase perhaps similar to that housing a clock by Anthony Blackford of Warwick which was sold at Bonhams London sale of Fine Clocks 11th December 2007 (lot 167) for £110,400.Condition Report: The movement appears to retain all of its original wheelwork between the plates including the contrate and escapewheel. Both the going and strike trains will 'run' when motive power is manually applied. Pinion wear appears minimal except to the fly pinion where noticeable wear is visible. The plates are thin and have historic re-bushing and minor punching to the pivot holes. The pallets and backcock and pendulum are probably not original. The top edge of the front plate has two screws inserted into threaded holes - the purpose of these is unknown but is not considered to be indicative of alteration.The hand arbor is a recent replacement (original is included with the lot) as is the strike release detent arm. The hour wheel, star wheel and calendar drive pinion assembly are also of recent making as is the calendar pin-wheel screwed to the rear of the dial. A calendar ring is present and again is most likely of recent manufacture. The calendar rings outer diameter is presently too large hence it will not fit between the four dial feet; the outer edge needs 'turning down' before it will fit however the spacing of the numbers etc appears to indicate that once this has been done the ring can be fitted.The dial is in good original condition retaining old thick gilding to the plate. The calendar aperture has been part-filled to allow shaping of the aperture to match positioning of the numerals engraved on the disc present with the lot. The chapter ring has traces of old silvering - the feet are unusual in that they are long and double-drilled so that they also serve and the dial feet. The hand present with the movement is not original.The present lot generally survives in good original condition with stalled restoration mainly limited to the under dial/calendar work; the restoration has not been completed due to the previous owner passing away.There are no weights included in the present lot. Condition Report Disclaimer

A WILLIAM III BRASS LANTERN CLOCK JONATHAN GREENHILL, MAIDSTONE, CIRCA 1695The posted countwheel bell striking movement with Huygens's endless winding and later anchor escapement regulated by seconds pendulum swinging outside of the frame of the clock to the rear, the dial with leafy scroll engraved concentric band issuing from a rose bloom at six o'clock to centre within applied Roman numeral chapter ring with fleur-de-lys half hour markers, signed Jn'o Greenhill, at Maidstone to lower margin and with engraved leafy infill to angles, the frame with column-turned corner posts beneath dolphin inhabited foliate pierced frets, vase finials and domed bell bearer, the sides now with japanned metal doors and the rear with hanging hoop over conforming backplate, (originally with verge escapement regulated by pendulum swinging between the trains, alarm removed and lacking feet).36cm (14.25ins) high, 17cm (6.75ins) wide, 19cm (7.5ins) deep. John Greenhill is recorded in Loomes, Brian Clockmakers of Britain 1286-1700 (noting research by Michael Person) as born in Maidstone in 1655 and gaining his freedom in 1674. As well as a clockmaker he was also a gunsmith, he married Alice Harris (sister of the clockmaker Walter Harris) in 1680 and died in 1712. Loomes notes several longcases are known and two lantern clocks including an example signed 'Johannes Grennell de Maidston fecit'.Condition Report: The trains have been re-pinioned and the escapement converted from verge with centre-swinging pendulum to anchor with long pendulum swinging at the rear. The alarm mechanism has also been removed otherwise movement is in good original condition but is very dirty/dusty and running with chains. The dial has been cleaned in the past hence has lost its silvering to the chapter ring; the alarm disc is also no longer present otherwise appears to be in good original albeit dirty condition. The frets appear original although the right hand is missing a securing lug and both lugs have been repaired on the left-hand fret. Frame is missing its feet otherwise is in good original condition; the rear panel and side doors are replacements. Clock has pendulum and a weight. Condition Report Disclaimer

A WILLIAM III MONTH DURATION LONGCASE CLOCK MOVEMENT AND DIALGEORGE ETHERINGTON, LONDON, CIRCA 1695-1700The six finned pillar bell striking movement with high-position external countwheel and anchor escapement for regulation by a seconds pendulum, the 12 inch square brass dial with subsidiary seconds dial, scroll decorated calendar aperture and ringed winding holes to the finely matted centre, within applied silvered Roman numeral chapter ring with sword hilt half hour markers, Arabic five minutes beyond the minute track and signed Geo. Etherington, London to lower margin, with later pierced steel hands, the angles applied with twin cherub and crown pattern spandrels incorporating foliate scroll engraved infill to margins between, (no pendulum or weights).31cm (12.125ins) square, 14.5cm (5.75ins) deep including seatboard. George Etherington is recorded in Loomes, Brian Clockmakers of Britain 1286-1700 as being made a Free Brother of the Clockmakers' Company in 1684 having previously being apprenticed to Robert Rooksby possibly in Newcastle-on-Tyne or York. In 1689 he moved from the 'Dial in Fleet Street' to 'against the New Church in the Strand', London. In 1697 he signed the Oath of Allegiance and became an Assistant of the Clockmakers' Company in 1701, Warden in 1706 and finally Master in 1709. He attended until at least 1720 and is thought to have died in 1729.Condition Report: The movement between the plates appears complete and in original condition with the only noticeable replacements being the escapewheel and pallets (historic 'service' replacements). The movement is somewhat dirty/dusty but there is nothing to suggest that trains would not run once a gentle clean/service has been undertaken. Externally the backcock is a replacement and the crutch has been repaired. The under-dial motionwork is complete including the calendar wheel. The dial is heavily discoloured with most of the silvering to the chapter ring worn-off. There are two 'tabs' riveted to the upper edge pf the plate indicating that an arch had been fitted at some point (now removed). The hands are relacements.Movement has an old seatboard (damaged) and two pulleys. There are no weights or a winding key included with the lot.  Condition Report Disclaimer

A WELSH GEORGE III OAK THIRTY HOUR LONGCASE CLOCKP. LLOYD, LAWHADEN, SECOND HALF OF THE 18th CENTURYThe posted countwheel bell striking two-handed movement with anchor escapement regulated by seconds pendulum, the 11 inch square brass dial with calendar aperture to the Prince-of-Wales feather decorated matted centre within applied Roman numeral chapter ring with fleur-de-lys half hour markers and Arabic five minutes to outer track, with scroll pierced steel hands and female mask and scroll cast spandrels to angles, in a case with generous architectural cornice incorporating swollen frieze over hinged glazed dial aperture applied with slender three-quarter columns to front angles, the sides with conforming quarter columns set against bargeboards at the rear, the trunk with cavetto throat moulding over tall ogee-arch topped caddy moulded door centred with a parquetry star, on plinth base with stepped-ogee top mouldings and shallow moulded skirt.230cm (90.5ins) high, 52cm (20.5ins) wide, 30.5cm (12ins) deep. A P. Lloyd is recorded in Loomes, Brian Clockmakers and Clockmakers of the World as working in Llanhaden, Pembrokeshire in 1806. 

A FINE GEORGE II BRASS MOUNTED EBONISED TABLE CLOCK WITH PULL-QUARTER REPEAT ON SIX BELLSROBERT HIGGS, LONDON, CIRCA 1750The six pillar twin fusee movement with verge escapement regulated by short bob pendulum, pull-quarter repeat on a graduated nest of six bells and sounding the hour on a further larger bell, the herringbone-bordered backplate finely engraved with symmetrical foliate scrolls inhabited by Barianesque figural terms and centred with a strapwork bordered oval cartouche signed Rob:t Higgs., LONDON, the 7 inch brass break-arch dial with calendar and shaped false-bob apertures to the finely matted centre within applied silvered Roman numeral chapter ring with fleur-de-lys half hour markers and Arabic five minutes beyond the minute track, with scroll-pierced steel hands and Indian mask and scroll cast spandrels to angles beneath arch centred with a blued steel circular boss gilt engraved Robert, Higgs, LONDON within moulded surround flanked by foliate scroll infill and incorporating strike N/S selection switch beneath, the inverted bell top case with generous hinged brass carrying handle and double cavetto top mouldings over hinged front with raised half-round brass mouldings bordering the glazed dial and the scroll-pierced upper quadrant frets, the sides with conforming brass-bordered break-arch windows and the rear with door matching that of the front, on cavetto moulded skirt base applied with brass plate engraved Walter Long Esq'r, Rood Ashton Wilts to rear over cast squab feet.47cm (18.5ins) high with handle down, 26.5cm (10.5ins) wide, 17.5cm (7ins) deep. Provenance:The brass plate o the rear of the case suggests that the present clock was once the property of Walter Long, 1st Viscount Long (1854-1924). Viscount Walter Long served as a Conservative MP who, over his long career in politics, held the posts of President of the Board of Agriculture, President of the Local Government Board and Secretary of State for the Colonies amongst others. He was briefly appointed Chief Secretary for Ireland and, whilst in the house of Lords, became First Lord of the Admiralty. Viscount Long was also heavily involved with the Partition of Ireland under the Government of Ireland Act in 1920. He retired from the House of Lords in 1921 becoming Lord-Lieutenant of Wiltshire and died at his home at Rood House, Ashton, Wiltshire in September 1924, aged 70. Robert Higgs is recorded in Baillie, G.H. Watchmakers & Clockmakers of the World as apprenticed in 1743 and gaining his Freedom of the Clockmaker's Company in 1750. He worked from Sweetings Alley and took his brother Peter into partnership in 1770. James Evans is recorded by Baillie as also working from Sweetings Alley from 1773. In 1775 he went into partnership with Robert and Peter Higgs; the firm subsequently moved to Exchange Alley and continued in business until around 1825. The partnership of Higgs and James Evans specialised in producing clocks for the export market - particularly to Spain hence a significant proportion of surviving examples being annotated and signed in Spanish. The engraving to the backplate of the current lot is executed very much in the style described in Dzik, Sunny ENGRAVING ON ENGLISH TABLE CLOCKS, Art on a Canvas of Brass 1660-1800 in section three under the sub-heading Later phase baroque style engraving, 1715-1740 (pages 259-78). Furthermore the case, with its distinctive applied brass mouldings, is reminiscent of those housing clocks by Huguenot makers such as Claude DuChesne and Simon DeCharmes; a comparable case, (for a movement by DeCharmes) is illustrated by Dzik on page 267 (Figure 15.6).Condition Report: Movement is complete with no visible evidence of alteration or noticeable significant replacements. The mechanism has been maintained with old 'patinated' finish. Both trains are intact and essentially in working order however the going train is not currently running due to the false bob rubbing against its backing plate. Unfortunately the strike train is also not operating due to being locked by the pull-repeat mechanism which is also jammed. Although we can offer no assurances it is most likely that one the repeat and strike trains have been freed-up and adjustments made they will probably operate correctly. The dial is in good condition with a nice degree of mellowing to the silvering. The hour hand is a replacement. The movement seatboard is most likely a replacement -despite this there is no visible evidence to suggest that the movement and dial are not original to the case. The case is in very good original condition with finely executed frets and damage very much limited to minor veneer shrinkage and other age-related blemishes.Clock has pendulum (integral), case key but no winder. Condition Report Disclaimer

A FINE GEORGE III MAHOGANY QUARTER CHIMING TABLE CLOCK IN THE MANNER OF HENRY HINDLEYJOHN AGAR, YORK, CIRCA 1770The six distinctive double-baluster turned pillar triple fusee movement with rectangular plates measuring 8.5 by 7 inches enclosing greatwheels fitted to the narrow ends of the fusee cones, the going train with tic-tac anchor escapement incorporating offset pallets regulated by a half-seconds brass lenticular bob pendulum, the quarter train chiming the quarters on a graduated next of six bells and the strike train sounding the hour on a further larger bell, the backplate signed Jn'o Agar, YORK within a bold large rococo scroll engraved cartouche, the 7.5 inch arched brass dial plate applied with high-position silvered disc engraved with Roman numeral chapter ring and Arabic five minutes beyond the minute track, with scroll-pierced steel hands over rococo scroll cast spandrels to lower quadrants mirrored by another pair of castings bordering a further silvered arched plate incorporating STRIKE/SILENT selection to upper margin over pivoted steel hand and signature Jn'o Agar, YORK, in a solid mahogany bell-top case with hinged brass carrying handle and double-cavetto top mouldings over arched glazed dial aperture to the front door incorporating forty-five degree angles to the shut faces behind, the sides with arched scroll-pierced sound frets and the rear with rectangular shallow-arch glazed door set within the frame of the case, on ogee moulded skirt base with generous squab feet.56cm 22ins high with handle down, 31cm (12.25ins) wide, 22.5cm (9ins) deep. John Agar (senior) is recorded in Loomes, Brian Yorkshire Clockmakers as born around 1730 and made Free in the City of York as a clockmaker in 1760. He lived at Castlegate until at least 1809 and died in 1815. His son, also called John, was apprenticed to his father in 1766 and made Free in 1782; he pre-deceased his father in 1814.  The present clock exhibits strong similarities with the work of the celebrated York clockmaker Henry Hindley. In particular the distinctive design of the double baluster pillars, which follow those first used by Hindley in around 1742, and the fusees incorporating greatwheels positioned frontwards (against the narrow ends). The reason for this arrangement with the fusees is suggested by Rodney Law in his article HENRY HINDLEY OF YORK 1701-1771, PART II (published as an excerpt by The Antiquarian Horological Society) as devised to reduce the degree of friction at the larger front pivot which, with the standard arrangement, was most apparent after winding. Finally the escapement, incorporating offset pallets spanning a handful of teeth, is reminiscent of Hindley's deadbeat arrangement employed (mostly in conjunction with a half-seconds pendulum) in his table clocks, as drawn by Law in Figure 19.In addition to these direct similarities above, the current clock shares Hindley's high-quality standards with regards to finishing and eccentric approach to the dial layout. Indeed a clock by Hindley, incorporating the same configuration of high-position chapter ring over large arched strike/silent selection to the lower margin, is illustrated in Barder, C.R. The Georgian Bracket Clock 1714-1820 on page 63 (Plate II/45). The engraved signature cartouche to the backplate is perhaps a departure from Hindley's influence, however it is very well executed in the high rococo manner following the trends described in Dzik, Sunny ENGRAVING ON ENGLISH TABLE CLOCKs, Art on a Cavass of Brass 1660-1800 pages 357-64. Condition Report: The movement is in clean and original working condition with no visible evidence of alteration or noticeable/obvious replacements to the trains. The movement has a trip-repeat facility which is operational although there is no exit hole in the case foe a pull-cord. Two of the six quarter bells are lighter in colour than the others hence are probably replacements however they are in tune hence the sound is good. The dial is in good original condition with overall slight mottled mellowing to the silvering; the hour and minute hands are probably well made replacements, the strike/silent selection hand appears original.The case is generally in fine clean condition having most likely had cosmetic restoration work (cleaning and polishing) executed in the recent past. The case is constructed from solid (Cuban?) mahogany hence is very heavy/substantial. The caddy superstructure has probably become detached and been reset (visible relatively recent glue to interior); the side frets and feet are almost certainly also restorations. Case retains original locks and hinges and visible faults are generally very much limited to a few minor historic bumps, scuffs and other minor surface blemishes.Clock is complete with pendulum, winder and two case keys. Condition Report Disclaimer

Y A WILLIAM IV BOULLE LYRE-SHAPED CARRIAGE OR MANTEL TIMEPIECEDWERRIHOUSE, OGSTEN AND BELL, LONDON, CIRCA 1830The circular three pillar eight-day going barrel movement with underslung English lever platform escapement regulated by sprung monometallic balance, the backplate signed DWERRIHOUSE, OGSTON & BELL towards the upper margin, the 3.375 inch circular gilt Roman numeral dial with radial engine-turned centre and further signed DWERRIHOUSE, OGSTON & BELL to lower margin, with blued steel moon hands set behind hinged convex glazed gilt brass bezel with engine-milled insert, the lyre-shaped case with foliate cast and chased hinged gilt brass carrying handle applied to the leafy scroll engraved brass and tortoiseshell marquetry top panel positioned between out-swept side projections, over rosewood band to frieze, half-round mouldings bordering the dial aperture and concave sided cradle decorated with further brass marquetry scrollwork to front, the red-stained shell veneered sides following the curved outline of the front, the rear veneered in rosewood and incorporating a shaped downward-hinged door inset with a scroll-pierced and engraved brass sound fret, on skirt base applied with acanthus cast gilt brass upper mouldings over brass marquetry decoration to front and engine turned bun feet.22cm (8.5ins) high with handle down, 16.5cm (6.5ins) wide, 10cm (4ins) deep. The partnership of Dwerrihouse, Ogston and Bell are recorded in Loomes, Brian Watchmakers & Clockmakers of the World, Volume 2 as working at Davies Street, Berkeley Square, London in 1832-35.Condition Report: The movement is complete and in clean condition with no visible evidence of alteration or noticeable replacements. The movement is fully wound and the escapement is intact and will beat a couple of times when encouraged however the clock is currently not running most probably due to being 'gummed-up' with dry/sticky lubrication. Therefore a gentle clean/service is almost certainly all that is required to bring it back to reliable working condition. The dial is in fine original condition exhibiting only light mellowing/oxidation to the surface and slight rubbing to the signature area.The case generally has survived in very good original condition with no losses or noticeable lifting to the brass marquetry. The tortoiseshell veneers to the curved elements are in very good condition with a small patch pf lifting/delamination to the inside face of the left hand side projection and another to the right hand side around the 2 o'clock position. There is a small veneer loss/chip to the upper edge of the lower side scroll moulding to the right-hand side; the left-hand side has a larger chip to the leading edge of the same lip and two small corner chips and slight movement to the same section below. The lower vertical faces edges of both these mouldings are lacking thin finishing strips of veneer. The skirting is in good condition with only two very small edge chips to the right-hand side. The rear has some overall light but noticeable shrinkage cracking to the rosewood veneers otherwise is in good condition.Timepiece has a case key and a winder.  Condition Report Disclaimer

A WILLIAM IV ORMOLU MOUNTED EBONISED MANTEL CLOCK IN THE LOUIS XV TASTEBARWISE, LONDON, CIRCA 1830The five-pillar twin chain fusee bell-striking movement with keyhole-shaped plates and anchor escapement regulated by lenticular bob pendulum, the backplate with pendulum holdfast and signed Barwise, LONDON to centre, the 5 inch circular gilt brass Roman numeral dial with fine foliate scroll engraved centre and signed BARWISE, LONDON over number 670 to the chapter ring beneath SILENT/STRIKE selection switch to upper margin, with blued steel cruciform hands set behind hinged leaf-cast reeded gilt brass bevel-glazed bezel, the waisted case with surmount of a putto seated on scallop shell applied to the ogee-shaped upstand, over front applied with rococo scroll cast crest and shoulder mounts over floral spray decorated leafy cartouche to apron, the rear with keyhole-shaped door inset with foliate scroll-pierced sound fret flanked by conforming mounts to shoulders, on rococo scroll cast feet decorated with floral buds to knees.47cm (18.5ins) high, 24cm (9.5ins) wide, 16.5cm (6.5ins) deep. The life of John Barwise and his family are outlined by A.D. Stewart in his article Barwise & Sons: Watchmakers to the King. A brief history of family and firm published in the March 2014 issue of ANTIQUARIAN HOROLOGY (Vol IIIV No. 1 pages 621-34). Stewart notes that John Barwise was born into a clockmaking family in Cockermouth, Cumberland in around 1756. By 1780 he had moved to London where he opened a watch retailing business. Ten years later he married Elizabeth Weston with his address being recorded as 29 St. Martin's Lane where he remained until his death in 1820. Of their eleven children two (possibly three) died in infancy and two, John II (born 1795) and Weston (born 1793), subsequently joined their father in the family business. In 1800, such was his success, John Barwise I purchased a second house in Dulwich.In 1805 John Barwise I was one of the fifteen watchmakers appointed by The Board of Longitude to adjudicate in the dispute between John Arnold and Thomas Earnshaw regarding 'the respective merits of their chronometers'. On the 14th February 1811 Barwise was the victim of five highwayman who relieved him of a 'gold watch, greatcoat, and a guinea-and-a-half in cash' whilst en-route from Camberwell to Dulwich. This unfortunate occurrence may well have tempered Barwise's enthusiasm for his house in Dulwich as records indicate it was rented out to tenants by 1813. In around 1816 his sons, John II (who had just turned 21) and Weston, joined him in partnership with the business then becoming 'Barwise & Sons'. Shortly afterwards (probably in 1820) the firm obtained the Royal Warrant as watchmakers to King George IV.John Barwise senior died in 1820; by this time he was a wealthy man leaving two properties and substantial investments to his widow and children. The business was continued by Weston and John II in partnership, however this only lasted six years as Weston died in 1826 leaving the business in the hands of John II alone. It was at this time that John II married and moved from the family home at St. Martin's Lane to nearby 42 Craven Street; and then in 1840 to a spacious residence called East Lodge, near Acton which at that time was in open countryside. At around the same time John Barwise II entered into an alliance with the highly inventive Scottish Clockmaker Alexander Bain who was in the process of developing the first electric timepiece. Barwise and Bain subsequently filed a patent (No. 8743) for an 'Electro-Magnetic Clock' which was granted in January 1841; an example of which was then subsequently exhibited at the Royal Polytechnic Institution shortly afterwards.In 1842 John Barwise II was approached by Pierre Frederic Ingold (1787-1878) to assist in the creation of a watch factory which, by employing newly invented machinery, would be able to mass produce high quality watches at a much smaller cost than the prevalent hand-built movements available at the time. Barwise, along with Thomas Earnshaw junior, subsequently became managing directors of the newly established 'British Watch and Clockmaking Company'. The factory was established at 75 Dean Street but only lasted two years before closing due to financial difficulties mostly brought-about by poor reputation fuelled by pressure from rival watch component makers to whose livelihoods the factory posed a great risk. It would appear that John Barwise II had invested most of his personal wealth in the venture as he was declared bankrupt in 1846. With this he lost his house, East Lodge near Acton, but still managed to keep the business afloat - perhaps mainly due to the generosity of his father-in-law, Charles Baumer, who provided the family with a house at 7 Queen's Row, Camberwell rent free presumably until Barwise was back on his feet.In 1853 another former business Barwise partner the Calcutta retail Jeweller Robert John Lattey returned to London and became founder and auditor of the 'London & Eastern Banking Corporation'. With the resources of the Bank behind him Lattey (trading as Lattey and Company) took-on Barwise's debt and became owner of the business. It was at this point that John Barwise II stepped back from the firm with the overall management passing to the to the Swiss watchmaker, Jules Rochat who had joined the business in 1847. Unfortunately the situation did not improve under Rochat's tenureship as it subsequently transpired that the funds used to purchase the business were illicitly acquired, and in 1857 the London & Eastern Banking Corporation collapsed.After the 1857 liquidation of Lattey and Company the firm was acquired by the jeweller and Goldsmith Douglas Guillaume Cave and continued, again under Jules Rochat's management, until 1869 when bankruptcy again forced the company to change hands. The firm was subsequently continued under the Barwise name in the hands of several different owners up until 1988 with their last known address being 153 Fenchurch Street. Of John Barwise II, he is recorded in the 1861 census as being a 'chronometer maker out of business' and presumably still resided at 7 Queen's Row, Camberwell until his death in 1869. 

A FINE GEORGE III INLAID SATINWOOD QUARTER-CHIMING EIGHT-DAY LONGCASE CLOCK IN THE SHERATON MANNERJAMES WILSON, LONDON, CIRCA 1800The five pillar rack and bell striking movement with anchor escapement regulated by seconds pendulum and chiming the quarters on a graduated nest of eight bells, the 12 inch circular single-sheet silvered brass Roman numeral dial with subsidiary seconds dial, calendar aperture and signed James Wilson, London to centre, with pierced steel hands, Arabic five minutes to outer track and N/S strike selection lever at three o'clock, the case modelled on a design by Thomas Sheraton with gadrooned-carved ebonised cushion-shaped pad to the concave-sided pediment incorporating a basket-of-flowers decorated oval marquetry cartouche to fascia, over satinwood panel frieze and square hood door with brass bezel-edged circular glazed dial aperture bordered by oak-leaf inlaid quadrant panels within chevron edged crossbanded surround, flanked by slender reeded inverted baluster carved ebonised free-standing columns with leafy caps and bases continuing up past the frieze to support giltwood stylised pineapple finials, the sides with scroll-pierced rectangular sound frets and conforming ebonised half columns applied against bargeboards to the rear, the trunk with concave moulding over satinwood panel to throat and slender break-arch door veneered in satinwood centred with inlaid concentric circles within complex ebonised edge mouldings and flanked by inset ebonised slender baluster columns matching those of the hood to front angles, the plinth base with cavetto top mouldings over banded frieze and fascia centred with a shaped satinwood panel incorporating oval cartouche inlaid with floral still life, flanked by projecting reeded pilasters terminating with squat tapered feet with conforming banded frieze to lower edge of the panel between.227cm (89.5ins) high, 48cm (19ins) wide, 25.5cm (10ins) deep. James Wilson is recorded in Baillie, G.H. Watchmakers & Clockmakers of the World as gaining his freedom of the Clockmaker's Company in 1781 and working in Westminster, London until 1824.The case of the present clock is particularly interesting in that it clearly follows a design by Thomas Sheraton published in his 1802 publication the Cabinet-Maker and Upholsterer's Drawing Book'.Condition Report: Movement is complete with no visible evidence of alteration or noticeable replacements. Although it will run, strike and chime (once set-up) the mechanism is somewhat dusty/discoloured hence a gentle clean/overhaul is advised prior to putting into service. The dial has some slight spotting/discolouration to the silvering and light scratching around the winding holes otherwise is in good condition with minimal wear and rubbing to the engraving. The hands appear undamaged.The movement retains its original seatboard which rests on undisturbed cheek uprights hence movement and dial are original to the case. The case generally is in sound condition with faults mainly limited to minor bumps, scuffs, light shrinkage and other age-related blemishes. The superstructure has a centre hole indicating that a third finial was fitted at some point (no longer present). The front upper corner of the plinth is missing small length of ebonised moulding to the top of the projection strip pilaster. The plinth front panel has a horizontal shrinkage crack across the centre and the right hand hood fret has a small loss.Clock has pendulum (suspension spring lacking) three weights, a case key and a crank winder. Condition Report Disclaimer

A CHARLES II BRASS LANTERN CLOCKWILLIAM HOLLOWAY, STROUD, DATED (16)78The separately wound trains with brass cheeked pulleys now running with chains, the going train with reinstated verge escapement regulated by short pendulum incorporating anchor-shaped flutes to the bob swinging within the frame at the rear, the strike train sounding the hours on a bell mounted above the frame via a countwheel, the dial with vacant circle within concentric band of engraved scrolling foliage issuing from a flowerhead to the lower margin and interrupted by engraved signature William Holloway, of Stroud '78 to the upper edge, within applied silvered Roman numeral chapter ring incorporating wheatear half hour markers, with sculpted steel hand and radial leaf engraved infill to the corners, the frame with one-piece corner castings formed as Doric columns beneath vase finials with acorn shaped caps, the front and sides applied with symmetrical scroll pierced cast brass frets with the front incorporating foliate engraved detail, beneath domed bell bearer capped with a vase finial, with original concentric ring decorated brass side doors and iron hanging hoop to rear, on integral inverted acorn shaped feet.41cm (16.25ins) high, 16.5cm (6.5ins) wide18.5cm (7.25ins) deep. William Holloway is recorded in Loomes, Brian LANTERN CLOCKS & Their Makers as the son of the clockmaker John Holloway born in 1732 at Market Lavington, Wiltshire. In 1658 he moved, along with his father and younger brother Richard, to Stroud in order to take-on the workshop of the recently deceased John Snow. Holloway was married to Hester Hieron in 1664 and continued working until his death in 1694. William Holloway had three sons one of which, John, continued the business in Stroud after his death; the other two, William and Arthur, moved to London to pursue the trade in the capital.  William Holloway was a confident, accomplished and relatively prolific maker who used distinctive castings for his frames which appear almost unique to the Holloway family. His early clocks (1661 to circa 1680) used castings loosely based on the London second period style but were one-piece (i.e. finials and feet were cast integral with the posts) with tall slender finials capped by distinctive acorn turnings. Three examples by Holloway with this type of frame are illustrated in White, George English Lantern Clocks on page 246 (Figures V/78-80). The second type of frame used was much more akin to the standard London third period pattern but again employed one-piece castings and appeared to be short-lived as they are only seen on clocks dating to the first five or six years of the 1680's (see White, page 247, Figure V/81). The third pattern was again based on London third period practice but was much more generous with distinctly bulbous swellings to the finials and feet, two clocks with this type of frame are illustrated in Loomes, Brian LANTERN CLOCKS & Their Makers pages 207 and 209 Figures 13.8 and 13.13. Other traits of Holloways work include the continued use of separate winding for each train long after most other makers had adopted Huygens' single-weight endless rope system. Clocks with separately wound trains are characterised by having hour bell hammers positioned to the right hand side of the movement. Loomes suggests that Holloway may have continued this practice as it allowed straightforward disablement of the strike train by simply removing or not winding the strike weight. Another unusual feature peculiar to Holloway was that he often used four wheel trains in order to give a longer duration. The current lot is a typical of Holloway's first phase of work with one-piece castings incorporating acorn-shaped feet and caps to the finials. Indeed the clock can be very closely compared to another example by Holloway dated 1674 illustrated by George White on page 246 (Figure V/79).Condition Report: As catalogued the movement has been re-converted to its original configuration of verge escapement with short pendulum having previously been converted to anchor escapement regulated by long pendulum swinging outside of the case to the rear. The re-conversion has been executed to reasonable standard however the contrate and escapewheel are noticeable replacements due to having slightly different feel (mostly in their weight) to remaining original wheelwork. The potances are well-executed and appear to utilise the original holes; the anchor-shaped pendulum bob is probably a little heavy and has been re-attached using solder. The top plate has spare holes to the rear edge from the previous anchor long pendulum backcock and an enlarged slot beneath the escape wheel to provide space for the previous anchor pallets escapement. The going train second wheel arbor (original) has ben thinned adjacent to the pinion to allow additional clearance for the previous anchor escape wheel. In addition to the above evidence of previous conversion to anchor escapement to long pendulum there is an additional pair of pivot holes (towards the top of the front and centre movement bars) the indicating that the clock may have also been fitted with an anchor escapement with short pendulum (facilitated by increasing the train to four wheels). It is possible that the pendulum for this configuration utilised the same space as the present pendulum which would account for the slot cut in the bottom plate beneath the anchor-shaped bob to allow additional clearance for slightly longer pendulum. The backplate is no longer present and was most likely removed along with the alarm mechanism which would have been mounted to the exterior of the plate at the time of conversion to long pendulum. The original hanging hoop is still present; the corresponding spurs would have most likely been fitted to backplate hence it is most probable that the clock was housed in a tall 'pencil case' type longcase after conversion to long pendulum.Except for the escapement both trains appear to be entirely original and in good order; the pulleys probably originally ran with rope lines. Although the clock is in working order a gentle service/lubrication is advised. The dial is in good original condition with some historic scratching, wear and surface casting texture to the vacant centre where the alarm disc would have been (removed at time of conversion to long escapement); the hand appears original and is nicely made. The frame is in fine original condition and the frets appear original. The bell is a replacement (domed support appears original); the top finial is also a replacement. The side doors are rare original survivors.Clock has two lead weights. Condition Report Disclaimer

A GEORGE II WALNUT EIGHT-DAY LONGCASE CLOCKJOHN BERRY, LONDON, CIRCA 1730The five pillar rack and bell striking movement with anchor escapement regulated by seconds pendulum, the 12 inch brass break-arch dial with star-engraved subsidiary seconds dial, calendar aperture and oval signature plate engraved John Berry, London to the matted centre within applied silvered Roman numeral chapter ring with fleur-de-lys half hour markers and Arabic five minutes to outer track, with scroll pierced steel hands and female mask and scroll cast spandrels to angles beneath arch with star-centred Strike/Silent selection dial flanked by dolphin cast mounts, the case with blind scroll fret fronted box upstand to the domed caddy superstructure incorporating further fretwork frieze to lower margin, over architectural moulded cornice and scroll infill to the quadrants above the hinged break-arch glazed dial aperture applied with Doric three-quarter columns with brass caps and bases to front angles, the sides with rectangular glazed apertures and conforming quarter-columns set against bargeboards at the rear, the trunk with concave throat moulding over break-arch door veneered with book-matched veneers within herringbone border and crossgrain cavetto edge mouldings, the plinth base with ogee top mouldings over conforming herringbone bordered book-match veneered panel to fascia and caddy moulded skirt.236cm (93ins) high, 51cm (20ins) wide, 26cm (10.25ins) deep. John Berry is recorded Baillie, G.H. Watchmakers & Clockmakers of the World as working in London 1728-54.Condition Report: Movement is in clean working condition with no visible evidence of alterations and replacements The dial has some slight even 'mellowing' to the silvering and is generally in good condition with overall light oxidation and pleasing surface. The movement and dial retains what appears to be the original seatboard which rests directly onto the cheek uprights of case (which appear undisturbed) hence it is most likely that the movement and dial are original to the case.The case has at some point had well observed restoration work undertaken in the past and now presents as being in 'lived-in' country house condition. The caddy superstructure is a restoration/replacement with the upper part being removable. The veneers to the convex front section have some movement/lifting. The upper surface of the chin moulding (just in front of the hood door) has a veneer loss otherwise faults to the hood are limited to movement/lifting of the veneers and shrinkage to the mouldings. The trunk is in similar condition; the door is in good straight condition and retains original lock and hinges. Both sides exhibit slight bowing and mnor veneer chipping to the rear edges; the left hand side also has noticeable lifting/bubbling to the veneers. The base has seen some well-executed restoration work to the structure otherwise presents as in very similar condition to the rest of the case.Faults to the case are otherwise very much limited to minor bumps, scuffs, shrinkage, wear minor repairs and other blemishes commensurate with age and use.Clock has pendulum, two weights, a case key and a crank winder. Condition Report Disclaimer

Y A FINE DUTCH BRASS MOUNTED EBONY GRANDE-SONNERIE STRIKING TABLE CLOCK WITH MOONPHASE AND CALENDARJACOB HASIUS, AMSTERDAM, CIRCA 1740The four pillar movement with thick plates measuring approximately 8.75 by 6.375 inches enclosing fusee for the going train with verge escapement regulated short bob pendulum, the hour and quarter trains both with standing barrels secured to the frontplate and sounding the quarter followed by the hour on a graduated pair of bells every quarter hour, the backplate finely engraved with a sunburst mask flanked by foliate scrollwork incorporating ribbon-tied martial trophies over grotesque mask surmounted foliate strapwork bordered signature cartouche engraved Jacob Hasius, Amsterdam Fecit to lower margin, the 8 inch square brass dial with scroll-bordered shaped cartouche further signed IACOB, HASIUS, AMSTERDAM and incorporating date-of-the month aperture to the upper part of the matted centre, over twin shaped chamfer-cut sector apertures revealing month-of-the-year and day-of-the-week indications labelled in Dutch and engraved with their respective deities, within applied silvered Roman numeral chapter ring with stylised trident half hour markers, with scroll-pierced steel hands and lambrequin mask centred scroll cast spandrels to angles within a herringbone engraved border to the edges of the plate, the silvered arch with rolling moonphase set within very finely engraved surround incorporating lunettes and overall inhabited with Classical deities including Poseidon and Zeus together with other allegorical figures and trumpeting putti flanking an aperture for age of the moon to the apex, the ebony veneered bell-top case with scallop-shell centred scroll-engraved hinged shaped brass carrying handle and fine foliate scroll strapwork pierced and engraved fretwork overlay to both the convex upper and the tall concave lower sections of the superstructure incorporating central grotesque masks, urns and dolphins to the latter, over complex top moulding applied with fine chiselled brass vase finials above opening front incorporating brass fillet moulding bordering the glazed dial aperture and engraved winged cherub mask and scroll upper quadrant frets, the sides with circular over concave-topped scroll-engraved brass sound frets incorporating Classical portrait bust-centred cartouches, the rear matching the front, on cavetto moulded skirt base bound with strapwork scroll engraved brass over finely detailed hairy lion's paw feet.51.5cm (20.25ins) high with handle down, 31.5cm (12.5ins) wide, 20.5cm (8ins) deep. Provenance:Purchased at Christies Amsterdam sale of EUROPEAN AND NOBLE COLLECTIONS 14th December 2011 (lot 60) for 34,600 Euros. Previously the property of a Dutch private collector; with H. Brokke, Amsterdam in 1966, and the Dreesman Collection, circa 1928. Jacob Hasius is recorded in Baillie, G.H. Watchmakers & Clockmakers of the World as working 1682-1747. He had a workshop in the Jan Roodenpoortstorenteeg and is listed in the 'Register of Good Men' in 1704 and 1716. The specification of grande-sonnerie striking, triple calendar indication and moonphase, coupled with the exceptional dial engraving and the profuse use of pierced and engraved brass mounts to the case suggest that the present clock was made as a 'statement piece' most likely for a member of the wealthy Amsterdam merchant class.Condition Report: Movement is complete, fundamentally original and is in relatively clean working condition. The grande-sonnerie striking is operational however is prone to either counting the hours incorrectly or not tripping now and again suggesting that a gentle service is probably due. All the underdial-work for the calendar indications are present and operational but will most likely require some adjustment and synchronisation. The dial is in fine original condition with exceptional engraving to the arch. The centre hole (for the hands) has a correction (from the time of making) in the form of a filled part-circle beneath the present hole otherwise faults are very much limited to a visible rivet mark (for a calendar wheel carrier post) to the matting near three o'clock. The case has a vertical veneer patch repair to the left hand upright (bordering the brass fillet moulding for the gazed aperture) of the back door otherwise is in fine original condition with faults very much limited to minor bumps, scuffs, shrinkage and other age-related blemishes. The brass frets are complete and of fine quality with good strong engraved detail throughout.Clock is complete with integral bob pendulum and a winding key. Condition Report Disclaimer

A GEORGE III EBONISED TABLE CLOCK WITH TRIP-HOUR REPEATTHOMAS EARNSHAW WITH MOVEMENT SUPPLIED BY A. AND I. THWAITES, LONDON, LATE 18th CENTURYThe five pillar twin fusee bell striking movement now with anchor escapement regulated by lenticular bob pendulum, the geometric border engraved backplate with pendulum holdfast and signed Tho's Earnshaw, London to centre, the frontplate stamped A & I, THWAITES, 650 to lower edge, the 7 inch brass break-arch dial with calendar aperture and signed Tho's Earnshaw, LONDON to the silvered centre within applied silvered Roman numeral chapter ring with Arabic five minutes to outer track, with delicate pierced steel hands and foliate scroll cast spandrels to angles beneath arch centred with a STRIKE/SILENT selection dial flanked by conforming mounts, the break-arch case with hinged brass carrying handle to the ogee above cavetto moulded top over hinged front with brass fillet inset glazed dial aperture, the sides with rectangular brass fish scale sound frets and the rear with break-arch door set within the frame of the case, on stepped ogee moulded skirt base with brass bracket feet.38cm (15ins) high with handle down, 28cm (11ins) wide, 19cm (7.5ins) deep. Thomas Earnshaw was an important maker with regards to the development of the marine chronometer. He is recorded in Betts, Jonathan MARINE CHRONOMETERS AT GREENWICH, A Catalogue of Marine Chronometers at the National Maritime Museum, Greenwich as born in Ashton-Under-Lyne, Lancashire in 1749 and is thought to have been apprenticed to William Hughes of High Holborn in around 1763-70. He married Lydia Theakston at St. James's Church Piccadilly in 1769 and by 1774 the had three sons - Manasseh William (b. 1770), James (b. 1771) and Thomas (b.1774). The financial pressure of having such large family early in his career proved unsustainable causing Earnshaw to abscond to Dublin in 1774 before returning to surrender himself to the debtors prison. Earnshaw however managed to come to terms with his debtors and was soon back in business.Thomas Earnshaw proved to be a very talented maker in particular with regards to watch finishing. Indeed he taught himself the highly specialised trades of watch jewelling and ruby-cylinder making and by 1780 he had turned his attention to chronometer making. He is generally credited with the improvement of the detent escapement through the introduction of a blade-spring (replacing a less effective pivoted arrangement). Earnshaw was introduced to the Astronomer Royal, Neville Maskelyne for whom he made a fine regulator for the Armagh observatory in 1789 and, in 1792, he acquired his former master's premises in High Holborn from where he set-about producing chronometers. By 1795 he had refined his designs for pocket and marine chronometers allowing him to start to see the prosperity of his perseverance.In 1806 the Board of Longitude awarded Earnshaw with £3,000 in recognition for his work, however his nose was put out of joint by John Roger Arnold (son of Earnshaw's contemporary rival John Arnold) receiving the same sum. By this time his son, Thomas Junior, was partly running the business allowing him to semi-retire to a comfortable villa in Greenford. In 1815 Thomas Earnshaw still had an involvement with the business however by 1820 he had pretty much retired leaving the workshops in the hands of his son who continued there until 1854. Thomas Earnshaw died in 1829. Ainsworth Thwaites was apprenticed in 1735 and worked from Rosoman Row, Clerkenwell, London 1751-80. He was an accomplished maker who supplied the clock for the tower at the Horse Guards Parade. His son, John, was born in 1757 and took over the business presumably on the death of Ainsworth in 1780 before moving to Bowling Green Lane. He entered into partnership with Jeremiah Reed in 1808 and he firm subsequently became well known for supplying all forms of clocks and movements either wholesale for others to retail or signed by themselves. The partnership continued under John Thwaite's leadership from several addresses in London until his death in 1842. The business has subsequently passed through a series of successors and is still trading today from Rottingdean near Brighton.Ronald E. Rose in his book English DIAL CLOCKS provides data allowing clocks by Thwaites to be dated from their serial number (Appendix III page 239); from this list the serial number of the movement of the current lot suggests that it was made around 1773-74. However, the style of engraving and overall design/form of the clock would suggest a date of around 1795-1805. From this it is perhaps appropriate to suggest the movement was probably held 'in stock' by either Thwaites or Earnshaw before being used for the present clock.Condition Report: Evidence (in the form of a series of filled holes) indicates that the present movement was originally made with verge escapement regulated by short bob pendulum. The conversion to anchor escapement has been executed very well and probably early in the clocks life with minimal alteration to the plates. The present pendulum holdfast unfortunately obscures the signature; there is also a spare threaded hole to the right hand edge of the backplate indicating the position of the original verge pendulum holdfast hook. The movement otherwise is in good relatively clean original working condition although is probably due for a gentle service. The dial has overall light wear and discolouration to the silvering otherwise is in good original condition. The minute hand has an old repair. The case is in sound original condition with notable faults limited to front-to-back shrinkage cracking to the arch-top of the case and a slight warp to the front door causing the top to project forwards slightly. The front and rear doors retain their original locks and hinges; the base of the case has been scooped-out slightly to allow for the present lenticular bob pendulum. The metal mounts (handle, mouldings, frets and feet are fairly heavily tarnished/discoloured, otherwise faults to the case are very much limited to relatively minor bumps, scuffs, scratches, minor shrinkage and other age-related blemishes.Clock has pendulum, winding key and a case key. Condition Report Disclaimer

AN UNUSUAL FRENCH PORCELAIN PANEL MOUNTED GILT BRASS ALARM CARRIAGE CLOCK IN A ONE-PIECE CASEMOSER, PARIS, CIRCA 1840The two train countwheel bell striking movement with platform lever escapement regulated by sprung monometallic balance, the backplate signed Moser a Paris and numbered 8058 to lower margin, the inside lower edge of the frontplate further stamped 2453, the circular white enamel Roman numeral dial with pierced blued steel trefoil hands set within fine foliate scroll gilt brass rectangular mask incorporating a conforming enamel Arabic numeral subsidiary alarm setting dial to lower margin, the bevel-glazed one-piece case with rococo scroll cast hinged carrying handle over top glass applied with a raised oval porcelain plaque polychrome painted with an 18th century style female portrait within gilt cartouche and blue ground border set within canted gilt brass surround flanked by foliate scroll-pierced fretwork, the caddy moulded frame cast and chased in relief with fine fruiting foliage incorporating crossed ribbon decoration to uprights, the side glasses applied with conforming raised oval porcelain panels decorated with putti, each set between a pierced and engraved foliate strapwork crest and apron, the rear door with further large panel painted with an 18th century musician playing a lute within pierced upper and lower border infill, on repeating leaf chased cavetto skirt base with inset rounded angles.15cm (6ins) high with handle down, 10.5cm (4.125ins) wide, 9.5cm (3.75ins) deep. Recent research by Leigh Extence has established that Georges Moser was born in Switzerland in 1798. By 1823 he had moved to Paris and was located at 18 Grenier St. Lazarre (which became number 15 in 1825). In 1836 Moser had moved to Boulevard du Temple 9 and subsequently entered into partnership with Samuel Marti in 1840. The partnership was registered at the address Orleans-Marais 13 until 1843 when Moser left and returned to Boulevard du Temple 9 before moving to number 24 in 1846 and then finally to number 15 in 1850. In 1860 the business was registered with 'et Cie' and records ceased after 1863.Extence also notes that Georges Moser utilised movements supplied by Holingue freres who also supplied Paul Garnier and were an important part of the history of Drocourt.Condition Report: Movement is clean condition with no visible evidence of alteration or noticeable replacements. The strike and alarm mechanisms are fully operational; the going train will run but escapement sticks which is most likely due to lubrication drying-out. The dial enamel appear to be free from visible faults and the mask is in good condition with no visible wear or faults. The case is in very good original condition with minimal edge wear and discolouration to the gilding. The top glass has a slight chip to the rear edge and the rear door has a small chip to the lower right corner otherwise the glasses appear free from visible damage. The porcelain panels are in fine condition with no visible cracks or evidence of restoration; the gilt details show minimal wear.Clock has a winding key. Condition Report Disclaimer

A RARE WILLIAM III RACK-STRIKING LONGCASE CLOCK MOVEMENT WITH ELEVEN-INCH DIALJAMES DELANCE, FROME, CIRCA 1695The four (formerly six) finned pillar rack and bell striking movement with anchor escapement for regulation by a seconds pendulum and substantial steelwork for the rack striking mechanism, the 11 inch square brass dial with subsidiary seconds dial, scroll border engraved calendar aperture and ringed winding holes to the matted centre within applied silvered Roman numeral chapter ring with stylised fleur-de-lys half hour markers, Arabic five minutes to outer track and signed Jam's Delance, Froom fecit to lower margin, the angles with applied winged cherub mask and scroll case spandrels (lacking hands, pendulum and weights).32cm (12.5ins) high, 28cm (11ins) wide, 13.5cm (5.25ins) deep. James Delance is recorded in Loomes, Brian Clockmakers of Britain 1286-1700 as born in Downton, Wiltshire in 1655, he is believed to have learnt the clockmaking trade from Lawrence Debnam in Frome prior to moving to London in 1677 where he was admitted as a Free Brother to the Clockmakers' Company the following year. Delance remained in London until 1685 when he left the city and returned to Frome where he set up business in Cheap Street - probably succeeding Lawrence Debnam who died in 1683 at the age of 40. Delance is recorded as undertaking work on clocks for Lord Weymouth at Longleat from at least 1694 until 1703. By 1721 Delance had moved to Downton, Wiltshire and was still working in 1736.Condition Report: Between the plates the movement appears to survive in good original condition with the only noticeable replacements being the escapement pallets. The underdial hour strikework is intact and appears all-original although the rack assembly pivot has been relocated slightly. The centre minute pipe is fitted with an additional quarter rack indicating that at one time the clock also sounded the quarters. There are also spare holes to both plates (and a pivot post to the frontplate) indicating an additional hammer was fitted along with respective detents etc for quarter strike-work. In addition to this there are two pairs of vacant holes indicating that the movement was originally fitted with two additional pillars. Although essentially in working condition the movement is dirty/neglected hence will require a gentle clean/service before putting to use; the twelve-hour hour wheel (fitted to the hour pipe) also has a folded tooth which will require repair. The dial is in sound original condition although the lower right corner has a loss to the tip of the plate. There are also three slight casting/stress cracks to the edge of the plate. The matting is finely executed and is in good unworn condition except for a couple of light surface scratches. The chapter ring has some localised patchy discolouration, the spandrels appear original and are in good condition. As catalogued there are no hands, lines, pulleys, weights, pendulum or seatboard present with the current lot. Condition Report Disclaimer

A GROUP OF EIGHT FRAMED ENGRAVINGS RELATING TO ASTRONOMYFROM ENCYCLOPEDIA BRITTANICA, 1771-97Engraved by Andrew Bell (1275-1809) comprising plates 61, 62, 64, 65, 81, 86, 88 and 211 framed as one, together with a group of three assorted scientific prints, framed as one and a large bundle of loose engravings including Spheres and Globes... engraved by C. Cooke, 1789, (qty).The first eight plates 24cm (9.5ins) by 18.5cm (7.25ins) to margins; the framed group 117cm (46cm) by 53cm (21ins) overall. 

A FRENCH EMPIRE ORMOLU FIGURAL MANTEL CLOCK UNSIGNED, PARIS, EARLY 19th CENTURYThe circular countwheel bell striking movement with anchor escapement regulated by disc bob pendulum incorporating silk suspension, the circular silvered Roman numeral dial with radial engine-turned centre and steel moon hands set within gilt repeating floral bloom decorated bezel, the case emblematic of the sciences cast with a standing figure of a female in Empire dress reading a book standing beside a pedestal housing the clock movement surmounted by a small bookcase applied with a classical bust, a further stack of books and drawing instruments, the front relief decorated with twin winged female terms flanking a flaming lamp beneath the dial, and the left hand side with free-standing engine-milled column surmounted by a celestial globe, the plinth base fronted with large relief cast panel depicting two putti observing a globe, on leaf moulded skirt base with block feet cast with anchor motifs.44.5cm (17.5ins) high, 31cm (12.25ins) wide, 11cm (4.25ins) deep.Condition Report: Movement is complete and appears all-original. The going train will just about beat, the strike train is currently inoperative most likely due to grime and the countwheel being loose on its arbor, the mainspring however appears sound. The dial has overall discolouration/wear to the silvering, the numerals are heavily rubbed and the tip of the hour hand is missing. The case is complete and retains original gilt finish to the castings with only light rubbing to the high spots and edges. The flat areas to the platform tops, sides and rear have become evenly tarnished/discoloured. The 'bookcase' mount to the surmount is loose on its fixing (screw needs tightening from beneath which requires the movement to be removed). The protractor is also loose (lacks securing nut) and the rear left hand foot is also loose (lacks fixing bolt and nut).Clock has a pendulum but no winding key. Condition Report Disclaimer

A FINE FRENCH LOUIS XV STYLE PATINATED AND GILT BRONZE MANTEL CLOCK 'PENDULE A L'ELEPHANT' THE DIAL INSCRIBED FOR MASSON, PARIS, THIRD QUARTER OF THE 19th CENTURYThe circular eight-day two train bell striking movement with anchor escapement regulated by disc bob pendulum incorporating Brocot type regulation to suspension, the backplate stamped with A.C within a circle over serial number 2453 to upper left, JAPY FRERES Et CIE, G'DE MED, D'HONNEUR roundel to centre and further number 5 2 to lower edge, the 4.25 inch slightly convex circular white enamel Roman numeral dial inscribed Masson, AParis to centre and with generous Arabic five minutes beyond the minute track, the scroll-pierced gilt brass hands set behind hinged convex glazed guilloche scroll cast bezel, the case modelled in the manner of Jean-Joseph de Saint Germain or Jacques Caffieri with a gilt figure of Cupid holding aloft his bow set on billowing clouds surmounting the patinated bronze drum housing the movement incorporating hinged glazed rear cover matching that of the front and gilt flowering foliage to sides, over support modelled as a stylised elephant with its trunk aloft fitted with rococo scroll cradle for the movement on its back incorporating gilt saddle strap around its waist, standing on a naturalistically cast gilt base incorporating large flowerheads and rocaille scrollwork.41cm (16.25ins) high, 31cm (12.25ins) wide, 18cm (7ins) deep. The distinctive and particularly attractive design of the current lot is closely based upon mid 18th century models by the Bronziers Jean-Joseph de Saint Germain (1719-87) and Jacques Caffieri (1678-1755). The signature for 'Masson, AParis' is almost certainly a 'decorative' addition no doubt intended to add a further degree of visual authenticity to the clock (by giving impression that the clock was possibly made by Denis Masson a leading Parisian clockmaker active 1744-78). An apparently identical example (albeit with a signature for Pierre Lieurtier, Paris) was sold at Christies, New York sale of The Collection of David and Peggy Rockefeller: English and European Furniture, Ceramics and Decorations, Part II 10th May 2018 (lot 663) for $47,500.Condition Report: Movement appears complete and original. The going train will 'beat' the strike train is operational however is sounding continuously when released hence there is a problem with the gathering of the rack (requires adjustment or possibly a new gathering pallet - either way a routine repair for an experienced clockmaker). The dial is in very fine condition with no visible chips or cracks other than a tiny 'gnats bite' adjacent to the regulation square above the XII numeral. The case is in fine condition with no apparent faults. The elephant has had some slight water-based iron-red wash highlights applied as an attempt to soften the surface sheen a little; these can easily be rubbed-off revealing medium pewter/brown patination which is best described as being a little thin in places. The guilloche scroll cast bezel has received similar attention but this time to deaden some edge rubbing to the patination.Clock is complete with pendulum and winding key. Condition Report Disclaimer

A WILLIAM IV MAHOGANY EIGHT-DAY LONGCASE CLOCKGRAYHURST, HARVEY, DENTON AND COMPANY, CIRCA 1830The five pillar rack and bell striking movement with anchor escapement regulated by seconds pendulum, the 12 inch circular brass Roman numeral dial with subsidiary seconds dial and signed Grayhurst, Harvey, Denton & Co., STRAND, London to centre and with steel moon hands, the case with stepped gabled 'chamfer-top' upstand over cavetto cornice, fluted frieze and square front door centred with a convex glazed cast brass bezel, with cock-bead moulded quadrant panels to spandrel areas, flanked by canted angles and with rectangular scroll pierced frets to sides, the trunk with concave throat over shallow-arch top caddy moulded door fronted with fine flame figured veneer and flanked by conforming canted angles, the plinth base with generous cavetto top moulding and inset flame figured panel to fascia over moulded skirt.200cm (78.75ins) high, 49cm (19.25ins) wide, 24cm (9.5ins) deep. Michael Grayhurst is recorded by Britten, F.J. Old Clocks and Watches and Their Makers as working in partnership with James Harvey as gold/silversmiths, watchmakers and jewellers from 65, Strand from circa 1810. By 1834, they had grown to become Grayhurst, Harvey, Denton and Company at 64, Strand and by 1840, they had a second shop at 128 Regent Street. Condition Report: Movement appears complete and fundamentally all original with no visible evidence of alteration or noticeable replacements. Although the movement will run and strike is currently somewhat dirty/neglected hence will require a gentle clean/service before putting to use. The movement retains its original seatboard which rests on undisturbed cheek uprights of the case set at a level correct for positioning the dial in the hood aperture. There is no visible evidence of alteration or any other movement being fitted hence we are of the opinion that the movement and dial are original to the case. The dial has lost its silvering (is now lacquered brass) however the engraving shows no discernible wear; the hands also appear original and are undamaged.The case is generally in very good original unrestored condition. Both side frets to the hood exhibit substantial damage and losses however enough survives to allow appropriate replacements to be made; otherwise hood is in fine original condition albeit with heavy build-up of dirt and grime to the superstructure and wear around the bezel keyhole to the left-hand side. The trunk and base are in similar condition to the hood with major faults limited to the backboard joints being 'sprung' to the top left and behind the plinth. The trunk door retains original lock and hinges and exhibits minimal warping (front top left corner projects forward by around 5mm - can probably be adjusted out by packing the hinges). The plinth has some wear to the raised cockbeading bordering the plain pilaster uprights and the skirting has wear and staining to the surface. Faults to the case are otherwise limited to relatively minor shrinkage, bumps, scuffs and other age related blemishes commensurate with age.Clock is complete with pair of brass-cased weights, heavy pendulum, crank winder and a case key. Condition Report Disclaimer

A REGENCY INLAID MAHOGANY BRACKET CLOCKBARWISE, LONDON, CIRCA 1825The five pillar twin fusee bell-striking movement with anchor escapement regulated by half-seconds lenticular bob pendulum and shouldered backplate signed Barwise, LONDON to centre, the 7 inch circular silvered brass Roman numeral dial with repeat signature Barwise, LONDON to centre and spade hands set behind hinged convex glazed cast brass reeded bezel, the arched case with hinged brass carrying handle over foliate motif centred shaped line decorated panel beneath dial, the sides with rectangular brass fish scale sound frets, the rear with arch glazed door, on ogee moulded skirt base fitted with brass ball feet.39.5cm (15.5ins) high with handle down, 24cm (9.5ins) wide, 16.5cm (6.5ins) deep.The life of John Barwise and his family are outlined by A.D. Stewart in his article Barwise & Sons: Watchmakers to the King. A brief history of family and firm published in the March 2014 issue of ANTIQUARIAN HOROLOGY (Vol IIIV No. 1 pages 621-34). Stewart notes that John Barwise was born into a clockmaking family in Cockermouth, Cumberland in around 1756. By 1780 he had moved to London where he opened a watch retailing business. Ten years later he married Elizabeth Weston with his address being recorded as 29 St. Martin's Lane where he remained until his death in 1820. Of their eleven children two (possibly three) died in infancy and two, John II (born 1795) and Weston (born 1793), subsequently joined their father in the family business. In 1800, such was his success, John Barwise I purchased a second house in Dulwich.In 1805 John Barwise I was one of the fifteen watchmakers appointed by The Board of Longitude to adjudicate in the dispute between John Arnold and Thomas Earnshaw regarding 'the respective merits of their chronometers'. On the 14th February 1811 Barwise was the victim of five highwayman who relieved him of a 'gold watch, greatcoat, and a guinea-and-a-half in cash' whilst en-route from Camberwell to Dulwich. This unfortunate occurrence may well have tempered Barwise's enthusiasm for his house in Dulwich as records indicate it was rented out to tenants by 1813. In around 1816 his sons, John II (who had just turned 21) and Weston, joined him in partnership with the business then becoming 'Barwise & Sons'. Shortly afterwards (probably in 1820) the firm obtained the Royal Warrant as watchmakers to King George IV.John Barwise senior died in 1820; by this time he was a wealthy man leaving two properties and substantial investments to his widow and children. The business was continued by Weston and John II in partnership, however this only lasted six years as Weston died in 1826 leaving the business in the hands of John II alone. It was at this time that John II married and moved from the family home at St. Martin's Lane to nearby 42 Craven Street; and then in 1840 to a spacious residence called East Lodge, near Acton which at that time was in open countryside. At around the same time John Barwise II entered into an alliance with the highly inventive Scottish Clockmaker Alexander Bain who was in the process of developing the first electric timepiece. Barwise and Bain subsequently filed a patent (No. 8743) for an 'Electro-Magnetic Clock' which was granted in January 1841; an example of which was then subsequently exhibited at the Royal Polytechnic Institution shortly afterwards.In 1842 John Barwise II was approached by Pierre Frederic Ingold (1787-1878) to assist in the creation of a watch factory which, by employing newly invented machinery, would be able to mass produce high quality watches at a much smaller cost than the prevalent hand-built movements available at the time. Barwise, along with Thomas Earnshaw junior, subsequently became managing directors of the newly established 'British Watch and Clockmaking Company'. The factory was established at 75 Dean Street but only lasted two years before closing due to financial difficulties mostly brought-about by poor reputation fuelled by pressure from rival watch component makers to whose livelihoods the factory posed a great risk. It would appear that John Barwise II had invested most of his personal wealth in the venture as he was declared bankrupt in 1846. With this he lost his house, East Lodge near Acton, but still managed to keep the business afloat - perhaps mainly due to the generosity of his father-in-law, Charles Baumer, who provided the family with a house at 7 Queen's Row, Camberwell rent free presumably until Barwise was back on his feet.In 1853 another former business Barwise partner the Calcutta retail Jeweller Robert John Lattey returned to London and became founder and auditor of the 'London & Eastern Banking Corporation'. With the resources of the Bank behind him Lattey (trading as Lattey and Company) took-on Barwise's debt and became owner of the business. It was at this point that John Barwise II stepped back from the firm with the overall management passing to the to the Swiss watchmaker, Jules Rochat who had joined the business in 1847. Unfortunately the situation did not improve under Rochat's tenureship as it subsequently transpired that the funds used to purchase the business were illicitly acquired, and in 1857 the London & Eastern Banking Corporation collapsed. After the 1857 liquidation of Lattey and Company the firm was acquired by the jeweller and Goldsmith Douglas Guillaume Cave and continued, again under Jules Rochat's management, until 1869 when bankruptcy again forced the company to change hands. The firm was subsequently continued under the Barwise name in the hands of several different owners up until 1988 with their last known address being 153 Fenchurch Street. Of John Barwise II, he is recorded in the 1861 census as being a 'chronometer maker out of business' and presumably still resided at 7 Queen's Row, Camberwell until his death in 1869.Condition Report: The movement appears to be in good original condition with no visible alterations or noticeable replacements. The pendulum holdfast bracket is no longer present. The dial has slight overall mellowing and a few small patches of discolouration to the silvering otherwise is in good overall condition. The case is in sound original condition with notable faults limited to a veneer patch repair around the bezel keyhole to the left-hand side, there is also a spare hole just above the fret to the left hand side -this is left-over from the bezel clasp being re-positioned. The arched top veneer has only two small light shrinkage cracks and there is some slight movement in the panel beneath the dial (but no cracks or losses to the inlay). The brass fittings are somewhat tarnished/discoloured. Faults to the case are otherwise limited to minor bumps, bruises and other age related blemishes.Clock does not have a winder or a case key. Condition Report Disclaimer

AN UNUSUAL GERMAN PROVINCIAL OAK CASED WEIGHT-DRIVEN WALL CLOCKINDISTINCTLY SIGNED, WIPPERFURTH, DATED 1761The posted key-wound bell striking movement with four-wheel trains set side-by side and pivoted between vertical steel movement bars within an iron frame constructed with rectangular corner posts riveted to both the top and bottom plates, the going train with anchor escapement regulated by long lenticular bob pendulum and the strike train with gravity rack and vertically pivoted hammer for sounding on a bell mounted on top of the case, the 11 inch square oak dial panel applied with circular brass disc with ringed winding holes to centre within pewter Roman numeral chapter ring with stylised sword-hilt half hour markers, Arabic five minutes beyond the minute track and indistinctly inscribed Johan Jorg...., in Wipperfurth beneath 1761, Den 15, December to lower margin, with pierced steel hands and angles applied with wooden roundels within brass plate infill, in a case with cavetto cornice over moulded hinged glazed dial aperture to front and solid panel doors to sides, the rear with forged iron hanging loops to upper corners and the base applied stepped ogee mouldings.50cm (19.75ins) high, 44.5cm (17.5ins) wide, 19cm (7.5ins) deep. The overall design and layout of the movement of the current lot (albeit to a much smaller scale) is similar wall clocks made in the Comtoise region of Eastern France. 

Y A FRENCH LOUIS XV GILT BRASS MOUNTED SMALL BOULLE BRACKET TIMEPIECE WITH SILENT PULL QUARTER-REPEATANTOINE THIOUT, PARIS MID 18th CENTURYThe eight-day movement with tapered plates incorporating concave lower angles united by four angular baluster pillars pinned through the backplate signed Thiout AParis to lower margin, the silent pull repeat mechanism sounding on a bell mounted within the superstructure of the case, the 5.5 inch circular thirteen-piece cartouche numeral dial with convex white enamel centre within chapter ring with blue-on-white Roman hour numerals within rococo borders and Arabic five minutes to outer track, with sculpted blued steel hands the engraved cut brass and brown shell marquetry decorated case with seated putto surmount to the concave-sided superstructure veneered with leafy scroll decoration and applied with foliate mounts to angles over generous leaf cast arched cornice, the front with brass-framed arched glazed door enclosing marquetry decorated floor and back panel to interior and incorporating cast panel featuring an eagle grappling a serpent to apron, the surround decorated with leafy scrolls within line border, the sides with recessed arched windows within leaf cast surrounds over hipped swollen base sections, on feet cast as dragons with foliate apron between.49.5cm (19.5ins) high, 28.5cm (11.5ins) wide, 15cm (6ins) deep. Antoine Thiout is recorded in Baillie, G. H. Watchmakers & Clockmakers of the World as a 'very famous maker' born in 1692, appointed Jure in 1743 and dying in 1767. He is perhaps best known for his 1741 publication Traite d'horlogerie which is generally considered as one of the classic horological works of 18th century. Amongst his patrons were the duc d'Orleans and the Dowager Queen of Spain; examples of his work reside in many important European collections including a bracket clock in the Garde Meuble, Paris.Condition Report: Movement has been converted from verge escapement to anchor and the going train will run. The wheelwork of the repeat train is complete however the rack-pull lever is lacking (snail and starwheel are present). The spring box is intact and the train will run through. One of the two vertical hammer arbors are lacking as are both the hammer arms. The dial has hairline crack across the enamel disc centre and the I, IIII and VI cartouche numerals have small edge chips; the rear is lacking a securing latch otherwise dial is in good original condition albeit a little tarnished/discoloured and with finely worked hands.The case is in fine condition with faults limited to some light blooming to the shell veneers in places and some patchy tarnishing to some of the brass marquetry.Clock has a case key but no pendulum or winder. Condition Report Disclaimer

A WILIAM AND MARY THIRTY-HOUR LONGCASE CLOCK MOVEMENT WITH TEN-INCH DIALBEN WRIGHT, LONDON, CIRCA 1690The posted countwheel bell striking single handed movement with rectangular section uprights rivetted to both the top and bottom plates and anchor escapement for regulation by a seconds pendulum, the 10 inch square brass dial with matted centre within applied silvered Roman numeral chapter ring with stylised sword hilt half hour markers and signed BEN Wright, London to lower margin, with scroll-pierced steel hand and winged cherub mask and scroll cast spandrels to angles, (no pendulum or weight)31.5cm (12.5ins) high, 25.5cm (10ins) wide, 13.5cm (5.25ins) deep. Benjamin Wright is recorded in Loomes, Brian Clockmakers of Britain 1286-1700 as born circa 1664 and apprenticed in April 1678 to Abraham Prime. He gained his freedom of the Clockmakers' Company in 1685 and is believed to have worked from Bell Alley, Coleman Street, London until his death prior to January 1709/10. 

A GEORGE IV CARVED MAHOGANY BRACKET WITH TRIP-HOUR REPEATJAMES MCCABE, LONDON, CIRCA 1825-30The five pillar twin chain fusee bell striking movement with anchor escapement regulated by half seconds lenticular bob pendulum with geometric ring engraved bob and stirrup regulation, the geometric border engraved shouldered backplate with pendulum holdfast and conforming oval cartouche signed James McCabe, Royal Exchange, LONDON to centre, the 8 inch circular convex cream painted Roman numeral dial inscribed JAMES McCABE, Royal Exchange, LONDON, 1075 to centre, with blued steel fleur-de-lys hands and Strike/Silent selection switch at twelve o'clock set behind hinged convex-glazed engine milled bezel, the lyre-shaped case with generous fluted urn surmount to the triangular pediment over applied acanthus scroll and rosette bordered waisted ogee-outline front and conforming shaped sides, the rear with shaped rear door inset with a brass grille sound fret, on bead and foliate gadroon-carved moulded base with generous projecting foliate rosette carved bracket feet, (dial refinished).61cm (24ins) high, 40.5cm (16ins) wide, 23cm (9ins) deep. Provenance:Purchased by the vendor from Dukes, Dorchester sale of Silver, Jewellery and Furniture Thursday 9th April 1998 (lot 842) for £3,600 hammer. James McCabe junior succeeded his father of the same name was one of the most successful English clock and watchmakers of the 19th century. He was apprenticed to Reid and Auld of Edinburgh and was admitted to the Clockmaker's Company as a Free Brother in 1822. Around this time McCabe entered into a short-lived partnership with Strahan (probably Charles who gained his freedom of the Clockmaker's Company in 1815). From 1826 James McCabe managed the business alone from 97 Cornhill until 1838 when he was forced to temporarily relocate to 32 Cornhill due to a major fire at the Royal Exchange. It was at this time (1825-43) that Thomas Cole worked for McCabe before setting up his own to produce distinctive and highly decorative timepieces in his own unmistakable style. The business was subsequently continued by Robert Jeremy until his retirement in 1883. Condition Report: The movement is in fine clean working condition with no visible alteration or noticeable replacements. The dial finish has bee restored to a good standard and is now free from visible faults. The case is in good original condition. The rear door has a few small losses and historic veneer patch repairs to the veneer overlap and the top pin hinge needs re-securing. The surface finish to the rear and right hand sides are a little flat hence requires 'freshening-up' (but are not faded). The top has a small veneer patch repair to the front left hand corner and another to the apex at the rear, otherwise the case is in fine condition with good figured veneers and faults very much limited to very minor shrinkage and a few slight bumps, scuffs and other age related blemishes.Clock is complete with pendulum, a wander and two case keys. Condition Report Disclaimer

A vintage candlestick telephone with bell box.

A collection of brass and copper Far Eastern items, comprising an copper and brass comport, the top with a carved rim, 14cm high, together with three containers, off differing heights, all with engraved designs, a baluster jar with a carrying handle, with raised bird decoration, 14cm high and an Elephant and cow bell with a chain (7)

An early 20th century Chinese brass temple bell, mounted with a hanging bracket, decorated with dragons, 21cm H x 16cm W

Collection of silver plate and metalware. Including: two sauceboats, a bell, various condiment vessels, spoons and tongs

A tray of embroidered bell pulls, atomizer, cigarette case, carving etc

An antique brass hand painted wall bell

A weights bar and weights together with two dumb bell sets

A Vintage Brass Hand Bell with Turned Wooden Handle and Bone Finial, 26cms High

A Collection of Various Brassware to comprise Kettle with Amber Glass Handle Etc together with a Vintage Bronze Metal and Wooden Handled Bell

A signed Lester Piggott presentation photograph in silver Asprey frame,  the frame inscribed NIJINSKY - 1970, M. B-S WITH HAPPY MEMORIES C.W.E., 9.34 by 13.5in, with easel stand The initials on the photo frame to: Michael Bell-Syre (consignor's stepfather) from: Charles W. Engelhard owner of Nijinsky

A Bell Mag 4 Kevlar Pro Series 2000 autographed helmet  and another Bell crash helmet, twenty-two various motor sports baseball caps including Daytona 500 examples, (qty)

A large framed photograph of the Sheffield and Glasgow Representative Football Teams from the game that took place at Cathkin Park in 1899, taken by Geo Bell and Co of 152 Sauchiehall ST Glasgow, Sheffield are depicted in White shirts and Glasgow in stripes. The line ups feature famous players including Robert McColl, founder of the famous chain of newsagents and Ernest Needham, one of the first professional players to Captain England. The frame measures 25 by 19 and is in excellent condition.     The Sheffield v Glasgow games, known as the Inter City games, pitted what were regarded as the very best from the two Cities against each other and were staged from 1874 to 1960, at one time drawing huge crowds. All glass will be removed from framed and glazed items prior to posting and may result in delays to shipping your items. (This service is included in the cost of postage and packing). We can also totally remove all framing and mounts upon request to reduce shipping costs. Alternatively, lots can be collected in person by prior appointment from NN8 1RT.     

World Cup Mexico 1970 autographed page by England in ink of 20 squad members,  includes Moore, Bell, Osgood, Banks, Hunter, Charlton, etc.; sold with English edition programme and four different FDC v Bulgaria 2nd July 1970, v Brazil 7th Jul 1970, v Germany 14th July 1970 and interesting cover with World Cup winners 1966 stamp franked England last day holders 21st July 1970, (6)

A ZEISS IKON MOVILUX, A BELL & HOWELL 252 CINE CAMERA two miniature tripods, a set of vintage scales and a tin of sewing scraps and accessories